Jenn-Air Ice Maker Parts
Find your part
Enter your model number or a part number and click "Search"Here is an example model number plate:
Popular Jenn-Air Ice Maker Parts
Your Price
$119.07
Condenser Fan Motor Kit
PartSelect Number PS1957416
Manufacturer Part Number W10124096
This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move air across the condenser coil. Please note: The manufacturer has changed the appearance of the product from the original. The kit still functions the same as the original part. It is an OEM factory replacement. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands. Also, a helpful tip is to store food to prevent deterioration when the power is off.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
Josue from Jacksonville, NC
Seven year old condenser fan was making noise when it was running.
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.
Read more...
Your Price
$139.13
Replacement Ice Maker
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue. Read more...
PartSelect Number PS2121513
Manufacturer Part Number D7824706Q
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer wall. The ice maker can break from normal wear and accidental damage. If this happens, your refrigerator may no longer make ice cubes, or may not make enough cubes, and the part should be replaced. This model measures approximately 11 inches long and 5 inches wide. It’s constructed of plastic and metal, and comes in black/white/silver. This assembly includes the ice mold and the control device.
Fixes these symptoms
- Clicking sound
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- See more...
Installation Instructions
Bernie from Diamond Bar, CA
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue. Read more...
Your Price
$48.20
Capacitor
PartSelect Number PS11757023
Manufacturer Part Number WPW10662129
This capacitor (Refrigerator and Freezer Compressor Run Capacitor, Run Capacitor) provides the voltage or energy current required to start the compressor and keep it running. It allows the compressor in your appliance to easily cycle on and off. This capacitor mounts directly onto the compressor starting relay. If the capacitor is faulty the compressor may get unusually hot and draw excessive amperage. It the compressor overheats, it may fail to run until it cools down again. The compressor may also get noisy from overheating. If this part is totally electrically open, it is defective (often due to overheating) and needs to be replaced. The part measures 1 inch by 1-1/2 inches, and is constructed of plastic with two metal wire terminals. This item includes 1 capacitor, sold individually. This part comes in black.
Fixes these symptoms
- Clicking sound
- Freezer section too warm
- Fridge and Freezer are too warm
- See more...
Installation Instructions
garth from forest lake, MN
My refrigerator stopped cooling and the freezer section stopped freezing
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
Read more...
Your Price
$76.06
Recirculating Pump - 60Hz
PartSelect Number PS11740331
Manufacturer Part Number WP2313628
A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down into ice cubes. If you notice that your ice maker is no longer producing ice or there is no water flowing over the cooling plate, this could be due to the recirculating pump not working. Be sure to keep the pump clean and free of build-up. This pump is 5.75 inches in length, 4.75 inches in width, 4.25 inches in height and weighs 0.81 lbs. This is a genuine OEM appliance part that comes directly from the manufacturer.
Installation Instructions
Richard from North Wilkesboro, NC
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well
Read more...
Your Price
$8.44
Touch-Up Paint - White
PartSelect Number PS385132
Manufacturer Part Number 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Installation Instructions
Michelle from Richardson, TX
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Read more...
Your Price
$69.43
Refrigerator Water Filter
PartSelect Number PS8759230
Manufacturer Part Number F2WC9I1
Sold Individually, this OEM water filter is for refrigerators and 50lb freestanding ice makers. The water filter removes contaminants from the refrigerator water supply. It measures 2.5 inches deep, 2.5 inches wide and 8.5 inches high with a micron rating of 0.5 to 1. For the best results change the filter every nine months or 2000 gallons. Follow the instructions in your owner's manual when replacing the water filter.
Your Price
$63.71
Ice Maker Bin Thermostat
PartSelect Number PS11740332
Manufacturer Part Number WP2313633
This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce more ice or activate shut-off. The bin thermostat may need to be replaced if bin is overfilled, underfilled, or not producing ice. Thermistor can be tested with an ohm meter. This part is made of plastic and metal, and is white in color. This is an authentic part sourced from the original manufacturer.
Installation Instructions
Ray from Terry, MS
Ice maker overfilling with ice and would not stop production when full.
Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual.
Read more...
Your Price
$28.53
Water Tube Kit
PartSelect Number PS11730901
Manufacturer Part Number W10823511
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may need to be cut. This water tube transports water to the ice and water dispensers. If your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Ice maker not making ice
- Leaking
- Not dispensing water
- See more...
Installation Instructions
Trent from Tacoma, WA
water dispenser started leaking
i wasn't sure it was the inlet valve unit because the leak was at the water dispenser in the freezer door. after some research it looked like the water inlet valve located in the back lower part of the refrigerator was the problem. to replace, take off the cardboard cover, about 6 screws, you have access to the water inlet valve, disconnect the hoses (i think it goes without saying that you should have turned off the water to the frig) replace the inlet valve, connect hoses, turn water back on and you'll be back in business. very easy repair.
Read more...
Your Price
$58.48
Temperature Sensor
PartSelect Number PS11756166
Manufacturer Part Number WPW10548509
This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes the necessary wiring connector. You will find this part located in the water pump area of the ice cube maker. The function of this part is to determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir.
Installation Instructions
William from LANDRUM, SC
Ice maker would not make ice. I went through diagnostics and it showed the level sensor was not working. Water would continue filling the reservoir and not shut off to start making ice.
Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibility. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.
Read more...
Your Price
$35.65
Ice Maker Water Distributor Tube
PartSelect Number PS11738017
Manufacturer Part Number W10863947
The water distributor tube distributes water from the reservoir to the evaporator plate.
Installation Instructions
Gerald from ELMHURST, IL
The tunes were moldy and the pump didn't work.
The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years.
Read more...
Appliance Type
Related Parts
Popular Jenn-Air Ice Maker Models
Below are the most popular Jenn-Air Ice Maker models we have. Enter your model number in the search box to find your model.
- JIM158XBRS1 Freestanding
- JIM1550ARS Freestanding
- JIM158XYRS0 ICE CUBE MAKER
- JIM158XBRS0 Freestanding
- JIM158XWRS0 ICE CUBE MAKER
- JIM158XBCX1 Freestanding
- JIM158XBCX0 Freestanding
- JIM158XBCX2 ICE MAKER - FREESTANDING
- JIM158XYCX0 ICE CUBE MAKER
- JIM158XXCX1 ICE CUBE MAKER
- JIM158XYRS1 ICE MAKER
- JIM158XXRS0 ICE CUBE MAKER
- JIM158XXRS1 ICE CUBE MAKER
- JIM158XBRB1 Freestanding
- JIM158XXRS2 ICE CUBE MAKER
- JIM1550ACX Freestanding
- JIM1550ARB Freestanding
- JIM158XBRS2 ICE MAKER - FREESTANDING
- JIM158XBRB0 Freestanding
- UKI2000AXX
