This genuine OEM replacement part is a water filter for your fridge or freestanding ice maker. The filter is used to remove contaminants and particles from the water, to ensure a clean and fresh taste. The filter should be replaced every six to nine months, or after 2000 gallons of water have passed through, whichever occurs first.
If your refrigerators interior light is not working, the door light switch may be the part to replace. It activates the light as the door opens or closes and has two push-on wire connections. Unplug the refrigerator before installation, and confirm fit using your refrigerators model number. This is an OEM part.
Keep ice production in step with available bin space using this ice maker bin thermistor. The probe senses temperature changes as ice accumulates around it and sends that information to the control board, allowing production to pause when the bin is full. A failed sensor may cause overflowing, early shutdowns, or interrupted ice productio...Read moren. Replacing a faulty thermistor helps restore accurate temperature feedback. Disconnect appliance power before installation, handle the probe and wiring gently, and secure the sensor in its original mounting position This is an OEM part sourced directly from the manufacturer.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
Warm temperatures in a refrigerator or freezer may mean the condenser fan motor is not circulating air to cool the compressor and condenser coils. This OEM motor runs at 115 VAC, 1090 RPM, and 3 W. Verify fit for your appliance model. Disconnect power before checking it. Look for blade obstructions and check that the blade turns freely. If it does, test motor continuity with a multimeter.
For an ice machine with a regulator, this OEM solenoid water inlet valve supplies water to fill the reservoir. Confirm compatibility using your machines model number.
The ice maker uses this OEM drain pump to remove water from its reservoir during flushing. It is rated 12V AC, 13W, and 60Hz. Check compatibility using the appliance model number. Disconnect power before installation and wear work gloves.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door switch module wore out
40 of 55 peoplefound this instruction helpful.
Fred from Oceanport, NJ
Easy
Less than 15 mins
Pliers
Pull out old module... Remove 2 wires... Tape to inside wall [don't want them to fall down into side panel]..
Order new switch..
Fed Ex pkg came on 2nd day..
Install wires on switch... Press into opening... Check door light on..[OK] .. Done
Was this helpful?
Thank you for voting!
Water not refilling after initial batch of ice
19 of 20 peoplefound this instruction helpful.
Jonathan from WILLIAMSBURG, VA
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
The water filled on startup (actually over-filled, which was a clue). After that water was used to make ice, no new water came in so the recirculation pump just made whining noises in the mostly empty reservoir. Since water could come in (on start up) I reasoned it wasn't the water inlet valve, and everything else suggested the ice maker
... Read more was getting inaccurate info about how much water was in the reservoir. Turns out, the water recirculation pump has a water level sensor built in. So while the pump itself still functioned, the water level sensor inside had gone bad. Replacing the pump fixed the issue. There are videos online that show how to accomplish that, but it was pretty straight-forward. The dis-assembly was sometimes irritating because it's hard to see and maneuver around inside. It'll help if you put the machine closer to eye level. Pay close attention to videos that show the disassembly because there are a couple of tabs that are hard to find.
Read less
Was this helpful?
Thank you for voting!
Ice bin overfilling
16 of 21 peoplefound this instruction helpful.
Travis from N CHESTERFLD, VA
Very Easy
Less than 15 mins
Nutdriver
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plasti
... Read morec panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall.