My Orders
Jenn-Air Ice Maker Hardware
GET YOUR OFFICIAL Jenn-Air PARTS TO ENSURE VICTORY
Popular Jenn-Air Ice Maker Hardware
Sold individually.
Sold individually.
Sold individually.
Sold individually.
Installation Instructions
Charles from Brooklyn, NY
Water leaking out under door
The pump outlet gasket was sticking out and a screw was missing from the pump outlet housing. This was causing water to flood out under the door.
Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
... Read more
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher.
Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
... Read more
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher.
Read less
Metallic screw that is less than an inch long. Does not include the plastic washer.
Metallic screw that is less than an inch long. Does not include the plastic washer.
Installation Instructions
Kyle from Wimauma, FL
Black Cam was bren on lower door hinge
This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works
... Read more
like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.
Read less
Sold individually.
Sold individually.
Installation Instructions
Gayle from COUPEVILLE, WA
Replacing burning assemblies and rusted screws
Installing the 2 new burner assemblies worked great with the new screws. New screws however, did not work with the old burner assemblies that have rusted screws I wanted to replace. New burner assemblies are slightly taller that the old ones.
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Enrique from Tigard, OR
The refrigerator door was difficult to maintain closed
Because the lower cams are made out of hard plastic the repeated opening and closing of the door wore them out. The hardest part was taking all of the food that is normally stored in the door.
First step was to determine whether the screws were metric or US standard - they are metric. The next step was to remove the top hinge ... Read more in order to remove the door and replace the bottom cams and brackets. This took a couple of minutes, replacing the cams was about 5 minutes and putting the door back on the pivot and reattaching the top hinge was another couple of minutes.
If I had called a service tech they would have charged a minimum of two hour and for the parts. I estimate that I saved myself about $100.
First step was to determine whether the screws were metric or US standard - they are metric. The next step was to remove the top hinge ... Read more in order to remove the door and replace the bottom cams and brackets. This took a couple of minutes, replacing the cams was about 5 minutes and putting the door back on the pivot and reattaching the top hinge was another couple of minutes.
If I had called a service tech they would have charged a minimum of two hour and for the parts. I estimate that I saved myself about $100.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
Installation Instructions
Lynn H from MILL CREEK, WA
Hinge pin for drawer lid broke
1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the secu
... Read more
ring slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed.
Read less
This ice maker scoop is an OEM refrigerator part designed to retrieve ice from the ice maker bin. It is made of plastic and measures approximately 10 3/4 inches in length and 4 inches in width. The scoop is designed to fit inside the ice bin for easy access. You will need to replace the scoop if it is cracked, broken, or lost. Discard the old scoop and insert the new one into its designated compartment.
This ice maker scoop is an OEM refrigerator part designed to retrieve ice from the ice maker bin. It is made of plastic and measures approximately 10 3/4 inches in length and 4 inches in width. The scoop is designed to fit inside the ice bin for easy access. You will need to replace the scoop if it is cracked, broken, or lost. Discard the old scoop and insert the new one into its designated compartment.
This screw is sold individually.
This screw is sold individually.
Sold individually.
Sold individually.
Installation Instructions
Carol from Monroe, NY
Refrig making a lot of noise
The motor kit had only two wires coming out of it. The existing one in the refrig had 6. I spliced the 2 red to one black on the new part and 2 white to the other black wire on the new part. The two green I attached to a screw. I left the 6 wire harness in place just cut off the plug piece that went into the old motor, and spliced all my
... Read more
wires.
Worked great!
Worked great!
Read less
Sold individually. For white and almond models.
Sold individually. For white and almond models.
Installation Instructions
MILES from ALAMOGORDO, NM
Microwave Door Exterior panel was cracked and the handle was broken
I disassembled the door by removing three screws from the side opposite the hinges and pried (lifted) that edge up and rotated the panel away from the metal portion of the door towards the hinges. I assembled the new door panel by attaching the handle (2 screws). I attached the new door panel by starting at the hinge side of the door an
... Read more
d working towards the opposite end of the door. The last little bit was tough to get it to snap over the metal sub-door. I reinstalled the 3 screws to snug, not tight because I did not want to crack the plastic.
Read less