Haier Fridge Parts

This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.

The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depressed, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers.

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different than the original, but should function the same.

A leaking water line or empty ice bin may point to a faulty refrigerator inlet valve. This replacement assembly includes the valve and connected tubing used to direct water toward the dispenser and ice-making system. Before replacing it, inspect the water filter, supply line, fill tube, connectors, and household water pressure. Turn off the refrigerators power and water supply before opening the rear service area. Some refrigerators use flammable refrigerant, so do not pierce, heat, or damage any nearby sealed-system tubing. Install each water line in the correct port, secure the electrical plug, and watch the connections for leaks when service is restored.

If ice spills inside the freezer or the storage bin no longer slides correctly, a damaged bucket may be the cause. This replacement container collects and stores cubes made by the refrigerators automatic ice maker. Its simple plastic design allows the bin to be removed for serving or cleaning. Inspect the support rails and nearby ice-making parts before installation, since a bent guide or heavy ice buildup can also block movement. Confirm the appliance model and compare the new bin with the old one. Remove any stored ice, slide out the worn bucket, clean the mounting area, and insert the replacement evenly.

An ice maker that no longer fills, freezes, or releases cubes may need a new assembly. This replacement kit controls the full ice-making cycle, from receiving water to dropping finished cubes into the bin. It uses an updated design and may not look exactly like the original unit. Several connection pieces are included to support approved refrigerator setups, but only the pieces shown for the appliance should be used. Confirm the complete model number before ordering. Disconnect electrical power and shut off the water supply before installation. Inspect for a frozen fill tube or weak water flow, and follow the appliance instructions carefully when connecting the wiring.

An ice maker that fills slowly, makes undersized cubes, or leaks may have a faulty water inlet valve. This electrically operated valve controls when water enters the ice-making system. It should open during the fill cycle and close tightly afterward. Mineral deposits, damaged seals, or an electrical fault can interfere with its operation. Check for low water pressure, a clogged filter, kinked tubing, loose wiring, or a frozen fill tube before replacing the valve. Unplug the refrigerator and close the household water valve before beginning. Follow the appliance diagram, avoid damaging nearby tubing, and test all connections carefully for leaks when finished.

This refrigerator door bin is designed for installation on the left side of the refrigerator door, providing convenient and secure storage for condiments, jars, and other beverage or food items. Made from durable white plastic, it is an ideal replacement for a door shelf that is cracked, broken, or missing, helping restore organization and prevent items from tipping or falling when the door is opened. The bin is designed for a precise fit and reliable everyday use. Installation is simple and tool-free, with the bin snapping directly into place on the door liner for quick replacement.

Warm air entering around a refrigerator door can make the cooling system work harder. This white door gasket provides the flexible barrier between the fresh food door and the cabinet. Inspect the seal if the door closes poorly or if condensation appears near its edges. Dirt on the gasket, loose hinges, an uneven appliance, or blocked shelves can cause similar problems, so check these areas first. Confirm the refrigerator model before ordering because gasket size and mounting style must match. Disconnect power before service, remove the old seal without damaging the door liner, and press the replacement evenly into its channel.

Condensation near the door or a refrigerator that runs more often may point to a worn fresh food door gasket. This replacement seal helps limit the exchange of cold inside air and warm room air when the door is closed. Inspect it for cracks, tears, stiff areas, loose corners, or sections that no longer touch the cabinet. Also check that the appliance is level and the hinges hold the door straight. Before service, unplug the refrigerator and protect stored food. Follow the appliance diagram when removing the old gasket, clean the door channel, and press the new seal into place without stretching it.