Dishwasher Switches

Shop By Brand

Popular Dishwasher Switches

Your Price
$41.65
  In Stock
Flood Switch
★★★★★
★★★★★
(35)
PartSelect Number PS8690623
Manufacturer Part Number WD21X10519
This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if your washer is overfilling or underfilling with water. It is about 5.5 inches in length, and mostly black in color with a green tip.
Fixes these symptoms
  • Not cleaning dishes properly
  • Not draining
  • Not drying dishes properly
  • See more...
Installation Instructions
Jeff from AUBURNDALE, MA
No water flowing into dishwasher
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve. I extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch. Read more...
Your Price
$17.52
  In Stock
Interlock Switch
★★★★★
★★★★★
(14)
PartSelect Number PS1481922
Manufacturer Part Number WD21X10261
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. The interlock switch senses the door is shut and the dryer can begin. This part might need to be replaced if your dryer is not starting or is in process while the door is open. The black rectangular part of the switch is approximately 2 inches long and a 1/2-inch wide with two gold plates on either end. This is a genuine OEM part that is sourced right from the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Shuts off too soon
  • Will Not Start
  • See more...
Installation Instructions
Steven from EPHRATA, WA
interlock switch was bad. Prevents the dishwasher form running as it "thinks" the door is still open.
Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works. Read more...
Your Price
$33.68
  In Stock
Drain Solenoid and Bracket Assembly
★★★★★
★★★★★
(9)
PartSelect Number PS1481923
Manufacturer Part Number WD21X10268
This valve opens in order for the water to drain out of the dishwasher.
Fixes these symptoms
Installation Instructions
Hector from West Melbourne, FL
Dishwasher water will not drain.
Very easy about 5 min replacement, Checked electrical conductivity to verify I had a bad solinoid, after I received the new part. I removed and replaced part by only removing and re-installed 2 screws and spring. Dishwasher worked like new. Read more...
Your Price
$18.94
  In Stock
Switch Interlock
★★★★★
★★★★★
(8)
PartSelect Number PS1021382
Manufacturer Part Number WD21X10224
This switch interlock is found on your dishwasher door, and it must be actuated for the dishwasher to start. If your dishwasher door does not close properly, or if the machine will not start, you may have a problem with your switch interlock. This part is sold individually and is an OEM part, built specifically by the manufacturer.
Fixes these symptoms
Installation Instructions
MICHAEL from ORLEANS, IN
would not start
First I removed the 6 screws that hold the inside cover on the door.Then I remover the plastic cover over the switches,pulled out the switches and disconnected the 2 wires from each switch and connected connected them to the new switches exactly as they were on the old switches.Then reinstalled the switches in their holders.I then removed the plunger and spring from between the switches and installed the new spring and plunger exactly like the old one was installed.I reinstalled the door cover making sure everything was in it's place,I put the screws in the door cover and I was done.It was a very simple job. Mike Read more...
Your Price
$38.50
  In Stock
Overfill Control Switch
★★★★★
★★★★★
(2)
PartSelect Number PS11750031
Manufacturer Part Number WPW10195039
This part is also known as a float switch. This float switch, when activated, stops the flow of water into the dishwasher.
Fixes these symptoms
Installation Instructions
Dennis from AUBURNDALE, WI
water fill overflows at times
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires. Read more...
Your Price
$30.43
  In Stock
Door Switch
★★★★★
★★★★★
(3)
PartSelect Number PS11745501
Manufacturer Part Number WP8269209
This dishwasher door switch will shut your dishwasher off when the door is opened.
Fixes these symptoms
Installation Instructions
mike from lockport, NY
dishwasher quit halfway thru a wash cycle
first I noticed that the dishwasher wasn't making any noise. Then I saw that there were no lights on the control panel. I opened the door and found water dripping off everything... I closed the door and tried hitting every button I could see, nothing happened. I checked the breaker, it was ok, and since I did all the wiring myself, I knew that was ok too. So I pulled off the upper panel of the front door and got out the electrical schematic that came with the washer.
first stop, the TCO, the thermal cutoff, it's like an inline fuse. I got 120 volts going in and nothing coming out. Did an ohm check and it was open.
Found it locally and replaced it. Now I've power to the control panel but the washer still doesn't work
because the micro switch in the handle is broken and that turns out to be the original problem...
the stupid plastic handle broke the micro-switch which shorted the TCO...
Read more...
Your Price
$46.87
  In Stock
Float Switch
★★★★★
★★★★★
(2)
PartSelect Number PS3492842
Manufacturer Part Number 154773201
Water that fills your dishwasher lifts the float. When it reaches a certain level, the float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher.
Fixes these symptoms
  • Leaking
  • Not draining
  • Will not fill with water
  • See more...
Installation Instructions
steve from virginia beach, VA
No water to dish washer
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job. Read more...
Your Price
$44.54
  In Stock
Door Switches and Holder Assembly
★★★★★
★★★★★
(10)
PartSelect Number PS2099645
Manufacturer Part Number 99002254
This part senses when the dishwasher door is closed so the cycle can start, and prevents it from starting if the door is not closed. If the dishwasher will not start or will not close, you may need to replace the door switches and holder assembly, also known as the door latch assembly. The dishwasher will not start if this part is defective. It includes two switches and the holder, this part does not include the handle or screws. Tools needed are T20 torx driver, needle nose pliers, and 1/4 inch nut driver. This is a genuine OEM part that is sourced directly from the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Will Not Start
  • See more...
Installation Instructions
Robert from Johnson, VT
no power
remove the eight screws that hold the inside door cover to gain access to the door switch.
remove the four wire conections and replace with new new switch
Read more...
Your Price
$59.88
  On Order
Door Switch Kit
★★★★★
★★★★★
(5)
PartSelect Number PS358749
Manufacturer Part Number 4318273
This kit comes with 2 micro switches and a wire harness.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Will Not Start
  • See more...
Installation Instructions
Thomas from Dunwoody, GA
Broken latch on dishwasher prevented operation
Photograph or diagram how the wires connect to the switches before taking out the old assembly. I could have salvaged switches from the old assembly by pulling out the white pins (and avoided buying the new switch kit). There's only one way the pieces go back together, so the wire connections are the only point that required special care and attention. Read more...
Your Price
$38.33
  On Order
Float Switch Kit
★★★★★
★★★★★
(2)
PartSelect Number PS557009
Manufacturer Part Number 8193506
This kit includes the switch, lever, seal and standpipe. Water that fills your dishwasher lifts the float, and when it reaches a certain level, the float acts as a trigger for the float switch. The float triggers the switch to shut off, thereby shutting off the flow of water into the dishwasher.
Fixes these symptoms
  • Leaking
  • Not draining
  • Will not fill with water
  • See more...
Installation Instructions
Robert from Rochester, NY
Dishwasher leaked under right front corner. Discovered that overflow(float switch) was either sticking allowing fill to overflow or rubber gasket was deteriorated allowing water to leak through mounting hole.
Removed mushroom shaped float cover by simply pulling up. Cover simply slide down into switch which is mounted through the floor of the tub. Using an adjustable wrench loosened and removed plastic fastening nut allowing removal of switch assembly from below. Disconnected two wires from switch and attached replacement assembly, reinserted in mounting hole, reattached nut from top, reinserted float cap and job done! The only tricky part is that the switch needs to be mounted inside assembly, wires connected and snapped shut before reinserting. Not difficult once you figure it out, Also need to make sure rubber washer is inserted on the overflow tube before reinstalling. Keep track as you remove and simply reverse the order. Tried to obtain part locally and was told it would be 6-10 days before delivery. Order from Part select arrived in 2 days. Read more...

Brands