Official Tappan Stove Parts | Order Today, Ships Today

Your Price

$19.06

Light Bulb

★★★★★

(11)

PartSelect Number PS12751166

Manufacturer Part Number 316538904

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the internal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.

Installation Instructions

Colin from Hollis, NY

Ice-Maker and Water Dispenser not working.

First I disconnected the power cord, then removed the screws that held the bracket that holds the base for the water-filer in place. I then disconnected the water lines(intake and outflow). Next I removed the screws that held the water-filter's base in place. I then disconnected the release lock mechanism for the filter and finally removed the water-filter base. I did the reverse to install the new water-filter base. Previously I had tested the intake water line and noticed the water was flowing with enough pressure upto the water-filter's base but no water was exiting thru the outflow line, which leads to the Ice-Maker and Dispenser. I had tried changing the filter but that didn't solve the problem it was then I had realized that the Base was the problem. The actual problem was the spring-loaded valves for both the intake and outflow lines, which had a plastic prong that protrudes out of the base that is triggered by the filter when installed. The two prongs were worn-down so the filter wasn't activating the spring-loaded release valve to let the water thru. As for the light, I just unscrewed it. Read more...

Your Price

$10.52

LENS

★★★★★

(5)

PartSelect Number PS16218465

Manufacturer Part Number 5304524341

The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.

Installation Instructions

Jim from Harrison, MI

Lower baking element would not heat up.

Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim Read more...

Flat Style Oven Igniter – Part Number: 5303935066

Your Price

$70.52

Flat Style Oven Igniter

★★★★★

(46)

PartSelect Number PS470129

Manufacturer Part Number 5303935066

This is a flat style oven igniter used to light the oven burner in a gas range. When the element in this igniter glows white hot, the gas is released from the safety valves, which lights the oven burner. If your range is not heating properly, or not heating at all, it might indicate a problem with this part. If the element in the igniter is only glowing red or orange, or not glowing at all, it will need to be replaced. This is a shorter style igniter. It is 3.72 inches in length, and it features an 18-inch wire lead. This kit includes the igniter, an instruction sheet, a mounting bracket, and the two ceramic wire nuts needed for installation. This part has an amperage range of 3.2 to 3.6. Unplug your appliance before you start any repair work.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Gas smell
See more...

Installation Instructions

John from Darlington, SC

Oven quit heating.

After reading up on the problem of the gas oven not lighting I decided I needed to install a new igniter. I had read where some people just pulled a panel off the back and installed a new one.. yeah, no such luck with this model so I had to crawl into the broiler drawer space [which I had to clean out first]. Note, if you wear trifocal glasses you might as well close your eyes and replace it by feel because there is no way to tilt your head back enough to see what you are doing and still get both arms and your chest in a broiler. Also be sure to remove all cats and dogs from the area before starting. They seem to think they can help or it's a game of hide and seek and they want to hide with you.. they were no help at all.
Other than that, it was quite easy. Read more...

Main Terminal Block Kit – Part Number: 5304409888

Your Price

$15.12

Main Terminal Block Kit

★★★★★

(12)

PartSelect Number PS471605

Manufacturer Part Number 5304409888

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to operate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Installation Instructions

Timothy from Spring Valley, AL

Cord was not tightened enough by delivery crew.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful. Read more...

Your Price

$143.30

Bake Element

★★★★★

(6)

PartSelect Number PS978772

Manufacturer Part Number 318255101

This is a 2100 watt bake element for your oven or range. The element supplies heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. Simply remove oven racks to access the bake element. Use a Phillips screwdriver to remove the two screws that secure the element to the oven body. Electrical wires feature slip-on connectors for easy installation, but be sure to hold the wires forward so the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.

Fixes these symptoms

Element will not heat
Little to no heat when baking
See more...

Installation Instructions

James from Delaware, OH

Element showed a hot spot prior to failing open.

Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done! Read more...

Broiler Pan Grate Insert – Part Number: 5304494997

Your Price

$65.92

Broiler Pan Grate Insert

★★★★★

(3)

PartSelect Number PS9864838

Manufacturer Part Number 5304494997

This includes pan and insert.

Oven Light Socket – Part Number: 316116400

Your Price

$47.52

Oven Light Socket

★★★★★

(4)

PartSelect Number PS439060

Manufacturer Part Number 316116400

The oven light socket allows you to screw in a light bulb so that you can see the inside of your oven. The light socket is located in the back of your oven, so you will need to remove the back panel to access the socket for the repair. You will also need to remove the current light bulb and the light lens cover so that the old socket can be removed. As you will be working around electrical circuits for this repair, be sure to disconnect the power source from the oven before you begin work on the oven.

Installation Instructions

Paul from Spokane Valley, WA

Oven light receptacle broken - bulb base broke off

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall. Read more...

Temperature Sensor – Part Number: 316217002

Your Price

$47.99

Temperature Sensor

★★★★★

(15)

PartSelect Number PS820208

Manufacturer Part Number 316217002

The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut off the quick connect, and then wire together with porcelain wire nuts. The function of the oven temperature sensor is to measure the temperature in the oven and signal the other heating components. Before you begin this repair make sure to disconnect the power to the range. The tools required for this installation include a number two Phillips screwdriver or a number two square head screwdriver, and maybe a pair of wire strippers and crimpers.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Dan from Bellevue, ID

Oven not heating to desired temperature

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove. Read more...