This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.
The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of...Read more the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.
This is a 2100 watt bake element for your oven or range. The element supplies heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. Simply remove oven racks to access the bake element. Use a Phillips screwdriver to remove the two screws that secure the el...Read moreement to the oven body. Electrical wires feature slip-on connectors for easy installation, but be sure to hold the wires forward so the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.
This oven rack is a genuine OEM part that measures approximately 18 1/4 by 15 inches. It acts as a shelf for placing food while it cooks or bakes in your oven. You will find it inside the oven cavity, and you can adjust its height to different positions. If the rack is damaged, you might notice bent metal bars, broken welds, or loose conn...Read moreections. It can also get stuck when you try to slide it in or out of the oven. If you do not replace a broken oven rack, your food may cook unevenly, and there is a risk that the rack might unexpectedly collapse, causing spills or burns. To remove an oven rack, first make sure your oven is turned off and cooled down. Open the oven door and grip the rack with both hands. Lift the front end slightly and tilt it upward while pulling it toward you until it slides out completely. If it is stuck, you can try gently moving it back and forth or side to side. Using food-safe lubricants can also help in this situation. If you are replacing more than one rack, please keep in mind that this part is sold individually.
This broil element delivers powerful radiant heat for broiling, searing, and browning food inside your oven. Positioned at the top of the oven cavity, it operates at 3400 watts and 240 volts to ensure fast, even heating during broil cycles. A genuine OEM replacement, this element is ideal for restoring performance when your oven produces ...Read moreno heat, insufficient heat, or uneven heat while broiling. Installation is simple—disconnect power, remove the old element, and secure the new one in place for reliable operation.
This is a light lens retainer clip and it is used in conjunction with the oven on your range. This retainer clip secures the light lens to the oven cavity. The part is made entirely of metal, and it is thin and bow-shaped. The retainer clip is roughly 3.5 inches long and 2 inches wide. The most common reason for needing to replace this pa...Read morert is if your current one is damaged or missing. This clip is a genuine OEM piece sourced directly from the manufacturer.
This is a bulb clip, also known as a sensor clip or bulb holder, which is designed to hold the thermostat bulb in place within the interior of various models of ovens. This clip is made of metal, measures approximately 1-inch in length and is a genuine OEM part, but is sold by itself and without the thermostat itself. The thermostat bulb,...Read more also known as a capillary thermostat, is used to measure the interior temperature of the oven during operation, and this clip secures it. If you notice your oven heats unevenly, too little or too much, this clip may be rusted, broken or damaged and causing the thermostat bulb to not detect the internal temperature properly. To replace this clip, you will likely need your user manual and a screwdriver and/or wrench. You will first need to disconnect your oven from the wall outlet and remove it from the wall. Use your user manual to locate the thermostat and use your screwdriver and/or wrench to remove the panel covering it. Here, you can likely replace the old clip with the new one, and then reassemble your oven.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cord was not tightened enough by delivery crew.
109 of 174 peoplefound this instruction helpful.
Timothy from Spring Valley, AL
Really Easy
15 - 30 mins
Screw drivers, Socket set
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede
... Read mored are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Read less
Was this helpful?
Thank you for voting!
Element showed a hot spot prior to failing open.
29 of 34 peoplefound this instruction helpful.
James from Delaware, OH
Really Easy
Less than 15 mins
Screw drivers
Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done!