My Orders
Samsung Washer Switches
GET YOUR OFFICIAL Samsung PARTS TO ENSURE VICTORY
Popular Samsung Washer Switches
This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the control board when that is done. If your washer door is not locking or latching properly, the door switch is likely bad or broken and will need to be replaced. To replace this assembly, you will need a flat-head and Philips-head screwdriver. This part is a genuine OEM switch assembly and is sold individually, without any wire harnesses or securing screws.
This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the control board when that is done. If your washer door is not locking or latching properly, the door switch is likely bad or broken and will need to be replaced. To replace this assembly, you will need a flat-head and Philips-head screwdriver. This part is a genuine OEM switch assembly and is sold individually, without any wire harnesses or securing screws.
Installation Instructions
Arthur from WILLARD, OH
The washing would stop in mid cycle and the door would be locked.
An initial issue was getting the door to unlock. I tired several things but finally was able to pull the door as if to open it and put something between the door handle and the front of the washer while I ran a washer cycle. There is a way to take the washer top off and reach down inside the unit and pull down on a release, but I did no
... Read more
t try that.
The washer has a rubber boot between the washer frame and the wash tub. There is a metal wire ring that secures the outer edge of the boot to the washer frame. Peel back the outer edge of the boot at the bottom to reveal a metal ring that has its ends connected by a small spring. Use a flat tip screw drive to pry this ring off. Peel back the boot from the washer frame.
Next use a Phillips screw drive to remove the two screws that protrude through the wash frame on the right side of the door.
Reach between the washer tub and the frame and the tub and pull the switch through the opening and the washer tub. You will have to wiggle the switch around to remove it. There are three sets of wires attached to the switch by plugs.
The switch is covered with a plastic protective cover. Remove this. You will have to use a screw driver to release various catches to do this.
Remove the three set of wires. There are catches that secure the wire plugs in place. pry them back with a small screw drive.
Attach the new switch to the sets of wires.
Attach the protective cover to the switch. The wires feed through a small slot toward the bottom of the switch.
Slide the switch through the opening where you removed it. and re-attach it using the two screws.
Put the rubber boot in the channel in the washer frame. Replace the metal ring. This was the most challenging part of the repair for me. I had to play around with this to get it into position. You have to work it around the gasket and stretch out the spring.
By the way, The service was great and exceeded by expectations.
The washer has a rubber boot between the washer frame and the wash tub. There is a metal wire ring that secures the outer edge of the boot to the washer frame. Peel back the outer edge of the boot at the bottom to reveal a metal ring that has its ends connected by a small spring. Use a flat tip screw drive to pry this ring off. Peel back the boot from the washer frame.
Next use a Phillips screw drive to remove the two screws that protrude through the wash frame on the right side of the door.
Reach between the washer tub and the frame and the tub and pull the switch through the opening and the washer tub. You will have to wiggle the switch around to remove it. There are three sets of wires attached to the switch by plugs.
The switch is covered with a plastic protective cover. Remove this. You will have to use a screw driver to release various catches to do this.
Remove the three set of wires. There are catches that secure the wire plugs in place. pry them back with a small screw drive.
Attach the new switch to the sets of wires.
Attach the protective cover to the switch. The wires feed through a small slot toward the bottom of the switch.
Slide the switch through the opening where you removed it. and re-attach it using the two screws.
Put the rubber boot in the channel in the washer frame. Replace the metal ring. This was the most challenging part of the repair for me. I had to play around with this to get it into position. You have to work it around the gasket and stretch out the spring.
By the way, The service was great and exceeded by expectations.
Read less
This part is a door lock switch assembly and it is made to work with your washing machine. The purpose of your door switch is to lock the door of your washer during the washing cycle. This will prevent the door from opening during this time. If your current part is faulty you may be experiencing leaking the door not staying closed or your appliance having trouble starting. This assembly includes the door switch and the lock. To make this installation you will need a Phillips screwdriver a flat-head screwdriver and locking pliers.
This part is a door lock switch assembly and it is made to work with your washing machine. The purpose of your door switch is to lock the door of your washer during the washing cycle. This will prevent the door from opening during this time. If your current part is faulty you may be experiencing leaking the door not staying closed or your appliance having trouble starting. This assembly includes the door switch and the lock. To make this installation you will need a Phillips screwdriver a flat-head screwdriver and locking pliers.
This door lock switch (part number DC34-00028A) is for washers. Door lock switch DC34-00028A locks the washer door to prevent the door from opening during the wash cycle and the spin cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
This door lock switch (part number DC34-00028A) is for washers. Door lock switch DC34-00028A locks the washer door to prevent the door from opening during the wash cycle and the spin cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This door lock switch assembly ensures the appliance operates only when the door is securely locked. Reliable locking improves safety and performance consistency. Replacing a faulty switch restores proper operation and protection.
This door lock switch assembly ensures the appliance operates only when the door is securely locked. Reliable locking improves safety and performance consistency. Replacing a faulty switch restores proper operation and protection.
