Samsung Washer Sensors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Samsung Washer Sensors
Your Price
$40.02
In Stock
Samsung Washer Thermistor
PartSelect Number PS4204984
Manufacturer Part Number DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of needing a new thermistor is the dryer cycle not working. Before installing this part, you should disconnect your dryer from its power source. We also recommend you wear work gloves to protect your hands during this installation. To make this repair, the tools you will need include a multi-screwdriver, a Phillips head bit, and a flat-head bit.
Fixes these symptoms
- Not Heating
- Too hot
- Won’t Start
- See more...
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$16.07
In Stock
Samsung Washer Moisture Sensor
PartSelect Number PS4206812
Manufacturer Part Number DC61-02627A
This moisture sensor plate is specifically designed to fit with your Samsung dryer. It is made of stainless steel and measures approximately 5 inches long. It is designed to detect the amount of moisture in the clothes, and it sends signals to the control board when the clothes are dry so that the dryer can end the drying cycle. If your dryer is not heating up properly or you find that your clothes are still damp at the end of the cycle, then the moisture plate sensor is likely malfunctioning.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Eric from CHAMBERSBURG, PA
Dryer getting warm but turning off before clothes dry
Cleaned the sensors from inside the drum with alcohol and that did not work. Ordered two sensors. Lift top cover. Remove screws on each of the front side that secures front cover. Unplug door sensor and pull front cover towards you and lift at same time removing from frame. I own dogs and immediately noticed dog hair and surprisingly lint all over the place. Remove the screws from the lint trap. (Theres one you access from inside the drum.) Unplug your sensor wires. Remove lint trap. The sensors simply push in/out. While I was in there I removed the cover for the lint tube and cleaned it out good. Lint had started to gather around the fan. Reverse your process and your done. TIP: Keep your screws orderly as you unscrew them. If you have this problem, just a good cleaning of hair, lint, dirt may do the trick as it essentially packs around the plug of the sensors. I had already ordered my sensors so I just put them in. I took my time and cleaned good and it was about an hour. It could be done in 15-30 minutes easily.
Read more...
Your Price
$63.64
On Order
Samsung Washer Water Temperature Thermistor
PartSelect Number PS4214274
Manufacturer Part Number DC90-10128N
The thermistor monitors and helps regulator the water temperature in the washer.
Your Price
$111.43
In Stock
Your Price
$86.96
In Stock
Samsung Washer Water-level Pressure Switch
PartSelect Number PS4217080
Manufacturer Part Number DC96-01703B
The pressure switch senses and controls the water level in the washer.
Installation Instructions
Fredric from ROCKMART, GA
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Read more...
Your Price
$82.87
In Stock
Samsung Washer Vibration Sensor Assembly
PartSelect Number PS4216271
Manufacturer Part Number DC93-00278A
Your Price
$130.68
On Order
Your Price
$52.67
In Stock
Your Price
$81.84
In Stock
Your Price
$105.35
In Stock
Samsung Washer Pressure Sensor Assembly
PartSelect Number PS8764044
Manufacturer Part Number DC96-01703H
This water-level pressure switch (part number DC96-01703H) is for washers. Water-level pressure switch DC96-01703H senses and controls the water level in the washer. Unplug the washer and shut off the water supply before installing this part.
Related Samsung Washer Parts
- All Samsung Washer parts
- Samsung Washer Bearings
- Samsung Washer Brackets and Flanges
- Samsung Washer Caps and Lids
- Samsung Washer Circuit Boards and Touch Pads
- Samsung Washer Dispensers
- Samsung Washer Drums and Tubs
- Samsung Washer Filters
- Samsung Washer Hardware
- Samsung Washer Hinges
- Samsung Washer Hoses and Tubes
- Samsung Washer Knobs
- Samsung Washer Latches
- Samsung Washer Legs and Feet
- Samsung Washer Motors
- Samsung Washer Panels
- Samsung Washer Pumps
- Samsung Washer Seals and Gaskets
- Samsung Washer Springs and Shock Absorbers
- Samsung Washer Switches
- Samsung Washer Transmissions and Clutches
- Samsung Washer Valves