Samsung Washer Hardware

Your Price

$12.85

Samsung Washer Hex Head Bolt

★★★★★

1 Review

PartSelect Number PS4205366

Manufacturer Part Number DC60-40137A

This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bolts. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.

Installation Instructions

Samuel from NEEDVILLE, TX

Washer making noise a snow smoking.

Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in. Read more...

Videos!

Your Price

$7.47

Samsung Washer Hose Clamp

★★★★★

1 Review

PartSelect Number PS11743008

Manufacturer Part Number WP596669

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

Fixes these symptoms

Leaking
See more...

Installation Instructions

jeff from lindenhurst, IL

Washing Machine was leaking water

Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...

Videos!

Your Price

$9.62

Samsung Washer Hose Clamp

★★★★★

2 Reviews

PartSelect Number PS11740613

Manufacturer Part Number WP285655

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Stephen from Laveen, AZ

Drive Pump Leaked

It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on. Read more...

Your Price

$6.40

Samsung Washer Tapping Screw

PartSelect Number PS4133205

Manufacturer Part Number 6002-000520

This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.

Your Price

$6.40

Samsung Washer Tapping Screw

PartSelect Number PS4133148

Manufacturer Part Number 6002-000213

Your Price

$6.40

Samsung Washer Screw

PartSelect Number PS4133247

Manufacturer Part Number 6002-001122

Your Price

$8.55

Samsung Washer Hex Screw

PartSelect Number PS4133422

Manufacturer Part Number 6009-001522

Your Price

$26.82

Samsung Washer Bolt Assembly

PartSelect Number PS4217876

Manufacturer Part Number DC97-02412A

Assembly BOLT;SWF-P12,MOTOR/

Your Price

$21.45

Samsung Washer Screw

★★★★★

6 Reviews

PartSelect Number PS12349731

Manufacturer Part Number W11233072

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

Installation Instructions

Ronald from Northfield Center, OH

changing stove and dishwasher to match new frig.

I actually replaced parts on my black double stove to make it into stainless. We purchased a new frig and needed to replace parts on our stove and dishwasher so they would match. They look beautiful, all the parts shipped when they were suppose too. Ordering from this company was top notch. Would order again if needed. Read more...