Samsung Dryer Parts
Find your part
Enter your model number or a part number and click "Search"
Popular Samsung Dryer Parts
Your Price
$60.53
Idler Pulley Assembly
Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.
Ordered replacement wheel/arm.
One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new. Read more...
PartSelect Number PS11771601
Manufacturer Part Number DC93-00634A
Fixes these symptoms
- Noisy
- Will Not Start
- Will not tumble
- See more...
Installation Instructions
Noah from OXFORD, KS
Tension/Dead Man Wheel Broke/Shattered
Dryer would not start but electronics were working.Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.
Ordered replacement wheel/arm.
One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new. Read more...
Your Price
$43.35
Drive Belt
PartSelect Number PS4133825
Manufacturer Part Number 6602-001655
The drum belt attaches to the motor pulley and causes the drum to spin as the motor is rotating. The drum belt is made of black rubber. This is an easy repair and should only take a few minutes. This goes between the drive motor and the dryer drum. The belt may have broken, which will cause the drum to not turn properly. You will need to pull your dryer away from the wall and use your Phillips screwdriver to remove the screws on the back. This is an OEM product, shipped directly from the manufacturer.
Fixes these symptoms
- Noisy
- Will Not Start
- Will not tumble
- See more...
Installation Instructions
Christopher from SUGARLOAF, CA
The dryer turned on but the drum did not move when you pressed start even though It started it cycles.
I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you
Read more...
Your Price
$40.38
Drum Support Roller & Axle
PartSelect Number PS4221885
Manufacturer Part Number DC97-16782A
The drum support roller and axle, which includes the roller shaft and mounting clips, is used in dryers. This part holds the drum as it rotates on the support wheels. When the roller begins to wear out, it self lubricates, so no additional grease is needed. If your dryer is making odd noises then checking and replacing the rollers can be the solution to your problem. Make sure to unplug the dryer from the power source before beginning this replacement. Refer to the diagram and installation instructions provided by manufacturer.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Tad from MINOT AFB, ND
Loud noise like boots being ran through the dryer
YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in the front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.
Read more...
Your Price
$28.69
Thermistor
PartSelect Number PS4204984
Manufacturer Part Number DC32-00007A
This is a thermistor, also known as a dryer thermistor. The thermistor is attached to the blower housing, it will help regulate and oversee the temperature within the dryer. The most common symptom of needing a new thermistor is the dryer cycle not working. Before installing this part, you should disconnect your dryer from its power source. We also recommend you wear work gloves to protect your hands during this installation. To make this repair, the tools you will need include a multi-screwdriver, a Phillips head bit, and a flat-head bit.
Fixes these symptoms
- No heat or not enough heat
- Shuts off too soon
- Will Not Start
- See more...
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$24.42
Thermal Fuse
PartSelect Number PS4205213
Manufacturer Part Number DC47-00016A
This thermostat is a genuine OEM part and is manufacturer-approved for electric dryers. The thermostat is responsible for monitoring and maintaining the temperature inside the dryer during the drying cycle. A faulty thermostat could result in clothes getting burned because the heating element does not receive the necessary signal to stop producing heat. This is a dangerous situation and could also lead to a fire. Ensure that you disconnect the power source to your dryer before you conduct this repair. This thermostat is connected to the clothes dryer unit by two screws which are sold separately.
Fixes these symptoms
- No heat or not enough heat
- Shuts off too soon
- Will Not Start
- See more...
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$147.90
Heating Element - 5300W
PartSelect Number PS4205218
Manufacturer Part Number DC47-00019A
This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.
Fixes these symptoms
- No heat or not enough heat
- See more...
Installation Instructions
Cynthia from JOHNSTOWN, NY
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Read more...
Your Price
$191.17
Assembly DUCT HEATER;27-DRYE
PartSelect Number PS4220205
Manufacturer Part Number DC97-14486A
Fixes these symptoms
- No heat or not enough heat
- See more...
Installation Instructions
Mark from WEST SUNBURY, PA
Dryer stopped heating
I purchased wholesale heater element with sensors. Couple wires and bolts to attach. Trickiest part is disassembling the dryer to remove the old heating unit. You-tube it; it's gold.
Read more...
Your Price
$13.36
Moisture Sensor
PartSelect Number PS4206812
Manufacturer Part Number DC61-02627A
Fixes these symptoms
- No heat or not enough heat
- Shuts off too soon
- See more...
Installation Instructions
Eric from CHAMBERSBURG, PA
Dryer getting warm but turning off before clothes dry
Cleaned the sensors from inside the drum with alcohol and that did not work. Ordered two sensors. Lift top cover. Remove screws on each of the front side that secures front cover. Unplug door sensor and pull front cover towards you and lift at same time removing from frame. I own dogs and immediately noticed dog hair and surprisingly lint all over the place. Remove the screws from the lint trap. (Theres one you access from inside the drum.) Unplug your sensor wires. Remove lint trap. The sensors simply push in/out. While I was in there I removed the cover for the lint tube and cleaned it out good. Lint had started to gather around the fan. Reverse your process and your done. TIP: Keep your screws orderly as you unscrew them. If you have this problem, just a good cleaning of hair, lint, dirt may do the trick as it essentially packs around the plug of the sensors. I had already ordered my sensors so I just put them in. I took my time and cleaned good and it was about an hour. It could be done in 15-30 minutes easily.
Read more...
Your Price
$3.61
Retainer Clip
PartSelect Number PS4206169
Manufacturer Part Number DC61-01228A
Fixes these symptoms
- Noisy
- Will Not Start
- Will not tumble
- See more...
Installation Instructions
Vicky from BLOOMSBURY, NJ
Belt fell off because of belt roller on the tensioner melted, ciezed and fell off
Watched a video on utube, how to repair my 16 month old steam dryer. The hardest part was laying on my belly holding the spring loaded tensioner and slipping the belt on around the blower housing. Only cost me $23. Winning!
Read more...
Your Price
$34.67
Thermal Fuse
PartSelect Number PS4205212
Manufacturer Part Number DC47-00015A
The thermal fuse measures the air temperature inside your dryer drum, and turns the heat on and off to maintain the optimal temperature during the drying cycle. If your dryer will not start, dry clothes properly, or produce any heat during the drying cycle, it could be due to a faulty thermal fuse. The original fuse is riveted to the mounting bracket. You will need to take out the rivets to replace it. This replacement fuse comes attached to the bracket. This part is also known as a thermal limiter, or a safety thermostat. Other symptoms linked with a faulty thermal fuse include: the drum is too hot, or the drying cycle ends too quickly. Remember to disconnect the power from your dryer before beginning this installation.
Fixes these symptoms
- No heat or not enough heat
- Will Not Start
- See more...
Installation Instructions
Calvin from LEXINGTON PK, MD
DRYER HAD NO POWER AND WOULD NOT POWER ON.
NECESSARY REQUIREMENTS TO DISMANTLE AND TAKE OFF DRYER CASING USING SCREWDRIVER AND NEEDLE NOSE PLIERS TO REPLACE THERMAL FUSE LOCATED ON THEHEATING ELEMENT CASING.TOOK ME HALF HOUR REPLACED PART AND PROCEDED TO PUT EVERYTHING BCK IN PLACE.PLUGGED BACK INTO SOCKET .whalla IM UP AND RUNNING AGAIN.DIFFICULTY RATING 1 TO 10-3.thanks 4 your support this was not difficult or hard just required TIME & PATIENCE. Thank u once again.THIS SITE IS THE GREATEST.
Read more...
Appliance Type
Popular Samsung Dryer Models
Below are the most popular Samsung Dryer models we have. Enter your model number in the search box to find your model.
- DV42H5000EW DRYER
- DV42H5000EW Samsung Dv42h5000ew/A3-01 Dryer
- DV42H5000EW Samsung Dv42h5000ew/A3-00 Dryer
- DV42H5000EW DRYER
- DV42H5000EW Samsung Dv42h5000ew/A3-02 Dryer
- DV42H5000EW DRYER
- DV42H5000EW Samsung Dv42h5000ew/A3-03 Dryer
- DV42H5000EW DRYER
- DV45H7000EW DRYER
- DV45H7000EW Samsung Dv45h7000ew/A2-01 Dryer
- DV45H7000EW DRYER
- DV45H7000EW DRYER
- DV45H7000EW Samsung Dv45h7000ew/A2-02 Dryer
- DV45H7000EW Samsung Dv45h7000ew/A2-00 Dryer
- DV40J3000EW DRYER
- DV40J3000EW Samsung Dv40j3000ew/A2-00 Dryer
- DV48H7400EW DRYER
- DV48H7400EW Samsung Dv48h7400ew/A2-00 Dryer
- DV48H7400EW Samsung Dv48h7400ew/A2-02 Dryer
- DV48H7400EW DRYER