This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Samsung Dryer Heating Element - 5300W
Troubleshooting
This part fixes the following symptoms:
Not Heating
This part works with the following products:
Dryer.
Part# DC47-00019A replaces these:
AP4201899, DC47-00019A
Customer Reviews
Average Rating:
★★★★★
★★★★★
17 Reviews
4.7
Filter By Rating:
5 Stars
15
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
1
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Timothy B - March 18, 2024
Verified Purchase
Great service
Fit like a glove works great
★★★★★
★★★★★
Meredith T - June 1, 2023
Verified Purchase
Perfect replacement
The part was as ordered, went with OEM to avoid having to replace it for another 10 years. It fitted perfectly and worked first time, and is still working a few weeks later.
★★★★★
★★★★★
Mark O - December 4, 2022
Verified Purchase
Item works as it should
Item works as it should. I'm not a mechanic or that mechanically inclined. I used online videos showing how to change the parts to fix my Samsung Dryer that was no longer drying because it was not producing heat. The videos make it look fairly easy, but, in real life, the parts don't always come out as easily as they look in the videos. Some parts were tightly stuck in place and required a bit of ingenuity to get them out.
I knew that the heating element was probably the part that needed replacing. It took me several hours to get all of the parts apart and finally get to the heating element. One thing that I did learn from this experience, wear gloves. I cut up two fingers on both hands because of all of the sharp sheet metal edges all over the dryer. One cut was fairly serious and I have the scar to show for it. In any event, I found the break in the heating element and knew it was the problem. I ordered the part and replaced it. It works like new now.
★★★★★
★★★★★
Heinz R - July 22, 2021
Verified Purchase
Exact part
Shipping was quick, box had some damage but the part was packed very well so there was no damage, verified the part number matched the original part, and the dryer is back in service working well.
★★★★★
★★★★★
James B - June 13, 2021
Verified Purchase
Easy swap out
Easy swap out of part. Had it overnighted and it came quick.
★★★★★
★★★★★
Jennifer W - April 1, 2021
Verified Purchase
Thanks PartSelect!
This is the second part that I have ordered from PartSelect, 1 was for my dishwasher and now 1 for my dryer. I am very impressed with PartSelect in knowing what part I need to fix my appliances. If I ever need another part, I will definitely choose PartSelect!
★★★★★
★★★★★
Lori W - March 3, 2021
Verified Purchase
Easy to find part, fast service
Part arrived in less than 2 weeks as promised. Works like a charm after my son installed it in my dryer. Couldn't ask for more.
★★★★★
★★★★★
Joshua P - June 10, 2019
Verified Purchase
Heating element for whirlpool dryer
Original heating element arrived on time. Great customer service.
★★★★★
★★★★★
Jennifer B - June 3, 2019
Verified Purchase
Great Part, Great Value
Everything came as noted and my dryer works!
★★★★★
★★★★★
Bob D - April 17, 2019
Verified Purchase
Got it fast
Easy to install, done deal.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 2.2 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timed dryer cycle was stuck on 1 minute, dryer wouldn't stop running unless door was opened.
Issue was the heating element coil, which had broken in places and shorted itself out. I removed the top and front panels to expose the heating element's housing. Then unplugged, removed and disassembled the housing to expose the heating element (there are many videos online that explain the process). Once the heating element was replaced
... Read more, the problem disappeared. Now the clothes are drying much faster than before. It is definitely worth getting the Samsung OEM part. Many reviews on generic equivalents were negative, despite how attractive the low price may look at first. PartSelect has never failed to impress with quick shipping and quality products.
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Have to remove top panel (screws on upper back), then control panel (screws on front), then front panel and door (screws on front). Good Luck, watch for sharp edges.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
12 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
October 27, 2017
My Samsung dryer has no heat. It is running fine and has no error code, just no heat! Is it the heating element or possibly something else?
For model number DV210AEW/XAA
Hi Joe, Thank you for the question. I suggest testing the thermostats and fuses on the element and blower housing with a multi meter to see if one of them are defective. The elements do not normally go. It is more then likely a thermostat or thermal fuse. Hope this helps!
26 people found this helpful.
Was this helpful?
Thank you for voting!
Janet
November 19, 2017
My Samsung dryer has no heat. It is running fine and has no error code, just no heat! Is it the heating element or possibly something else?Thank you.
For model number DV350AER/XAA
Hi Janet, Thank you for the question. There are a few parts you can test with a multi meter before replacing the element. The thermostat and Bracket assembly PartSelect Number PS4276292 and the High Limit Thermostat ,PartSelect Number PS4205217 on the element housing. In most cases one or both of these parts would need to be replaced when you have no heat.Usually if the element has burnt out you will see physical damage to the element.Hope this helps!
13 people found this helpful.
Was this helpful?
Thank you for voting!
Edward
April 9, 2019
How do you check heat element
For model number 402.89032010
Hi Edward, thank you for your question. To test your heating element you can test that with a multi meter and it should be reading between 0 - 50 ohms. I hope that helps. Good luck with your repair.
7 people found this helpful.
Was this helpful?
Thank you for voting!
Josie Woods
August 22, 2017
My dryer starts and then goes off. Error code he appears. Samsung service says the error code means heating element, but after reading the description of what this part is suppose to solve (if the heating element is burned, dryer does not heat or over heats, or clothes take to long to dry), the dryer does not stay on and an error code comes up. Is this in line with what occurs with this part #ps4205218 manufactory part #dc47 00019a? Thank you for your reply
For model number DX218AEW/XAA
Hi Josie,
Thank you for your inquiry. Yes, the HE error code is in relation to the heating element not working correctly. If your are getting the HE error code and the dryer is shutting off, see if the circuit breaker for the dryer has been tripped. If so, you will need to unplug the dryer and check the wire connections between the electronic control board and the heating element. If there are any loose wires reconnect them. If the wire harness or the heating element appears damaged replace them. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Dewane
February 20, 2018
Does this dryer have a heater element ? If yes can you give me part # , thanks
For model number Dv331aew/xaa
Hello Dewane, thank you for your question. I have researched the model you have provided and have found the part you’re looking for is Heating Element Part Number DC47-00019A. Good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
John
October 14, 2019
Dryer runs but does not heat up
For model number DV42H5200EF/A3
Hello John, thank you for writing. This is likely due to either a faulty Thermistor, part number PS4204984, or Heating Element, this part number PS4205218 for your model. Good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Calvin
January 31, 2019
My dryer is running but it isn't producing any heat. I replaced the heating element last year. Should i replace it again?
For model number DV50F9A7EVP/A2
Hello Calvin, thank you for your question. The heating element rarely goes bad. I would recommend testing the thermostats and fuse to determine if one of those parts are faulty. A faulty thermostat can cause the unit to run, but not heat. Testing the thermostats is a very easy job. Set your multimeter to the R X 1 setting. Take each of your meter's probes and touch one to each terminal. You are testing for continuity, and you should receive a reading of either zero or infinity. At room temperature, testing the thermostat should produce a reading of zero. But if a thermostat is tested when it is heated to its limit, a reading of infinity should be produced. We strongly recommend that you test your thermostat at room temperature. If the test you conduct with your thermostat does not produce these results, then you should replace the component. If the thermostats are tested and are fine, the element should be replaced. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sunila
May 15, 2019
Our Samsung dryer runs and dries the clothes but they come out super hot and when finished it keeps beeping with he error code. Can you please advise the part numbers that could be faulty in this situation. Thanks!
For model number DV42H5000EW
Hello Sunila, Thank you for the question. The HE error code means there is a Heating Error. Make sure the gas supply cut-off valve for the dryer is fully open. Unplug the dryer and reconnect any loose wiring connections on the gas valve coils. Replace the wire harness if damaged. Hope this helps!
Was this helpful?
Thank you for voting!
Willians
April 26, 2019
I got the heat element from part select, i installed but now i don’t see any song of power on machine. What can be wrong?
For model number DV42H5400EW
Hi Willians, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. If all of those parts are fine then the issue might actually be in your control board. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Jason
December 19, 2017
What is difference between part no. Dc97-14486a and dc47-0019a?
For model number DV218AEB/XAA-0000
Hi Jason,
Thank you for your question. This part is just your heating element. Part: Dc97-14486a is the metal duct around your heating element. I hope that helps. Good luck with your repair.
