RCA Range Parts
Popular RCA Range Parts
Your Price
$61.82
In Stock
RCA Range Bake Element
PartSelect Number PS249247
Manufacturer Part Number WB44K5012
At the floor of your electric oven is the bake element. This partially open-style element comes with push-on terminals. The bake element will likely provide most of the heat for baking. Therefore, if the oven is not heating properly, or if food is burnt on top and undercooked below, your bake element may be at fault. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, use a multi-meter to test for electrical continuity to see if the element needs replacing.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Timothy from Cordova, TN
Bake element cracked on its own
Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, turn on for a few minutes to make sure it works. Piece of cake.
Read more...
Your Price
$11.91
In Stock
RCA Range Drip Bowl - 6 Inch
PartSelect Number PS244697
Manufacturer Part Number WB32X107
The drip bowl on your range is designed to catch any spills that may occur when cooking. This drip bowl is chrome in color and is 6 inches in diameter. The chrome drip bowl is intended for use with rolled, terminal-style plug-in surface element units. The drip bowl is located beneath the surface element, so you will need to remove the element prior to swapping out the old drip bowl for a new one. Many of our customers have rated this repair as easy, and you will not require any tools to complete it. This part is sold individually.
Installation Instructions
Gregory from Princeton Junction, NJ
Control switch did not function and one burner worked only occasionally
First, I used the PatrSelect website, which has great prices, and has helpful diagrams. Once I had all the parts, I worked with my wife to turn off the power at our home junction box. Next, I lifted off the cover over the control area of this range. I removed four nuts to lift out the panel that holds the four controls and the fan switch. I removed the wires from the broken controls, removed the two screws holding each control in place, then screwed the new ones in place. I would recommend trimming the posts on the controls to the correct size before screwing them in place, because it is easier to grip them and not bend them when they are not mounted. I reconnected the wires and replaced the panel. For the "receptacle", I followed the instructions provided regarding cutting the wire and placing the wire nut and heat shrink tubing. I opened the unit that houses the burners to get easy access.
Read more...
Your Price
$22.05
In Stock
RCA Range Drip Bowl - 8 Inch
PartSelect Number PS244696
Manufacturer Part Number WB32X106
Drip bowls are located under the heating elements and catch grease and spills that come from cooking on your stove top. If your drip bowl is damaged or rusted, it could allow grease to drip inside your range. This 8 inch chrome drip bowl fits most electric ranges. Before you replace your damaged drip bowl, make sure the element is turned off and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and reattach the element. Make sure the small hole on the bowl lines up with the element socket. Drip bowls are sold separately.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Gregory from Princeton Junction, NJ
Control switch did not function and one burner worked only occasionally
First, I used the PatrSelect website, which has great prices, and has helpful diagrams. Once I had all the parts, I worked with my wife to turn off the power at our home junction box. Next, I lifted off the cover over the control area of this range. I removed four nuts to lift out the panel that holds the four controls and the fan switch. I removed the wires from the broken controls, removed the two screws holding each control in place, then screwed the new ones in place. I would recommend trimming the posts on the controls to the correct size before screwing them in place, because it is easier to grip them and not bend them when they are not mounted. I reconnected the wires and replaced the panel. For the "receptacle", I followed the instructions provided regarding cutting the wire and placing the wire nut and heat shrink tubing. I opened the unit that houses the burners to get easy access.
Read more...
Your Price
$51.32
In Stock
RCA Range INFINITE HEAT SWITCH KIT
2. Lift range lid.
3. Remove back panel. Loosen the 6 - 1/4" nuts, then lift up slightly, which compresses the "latch" at the top middle. Let down and panel comes off easily.
(Note: Do not remove wires yet)
4. Remove control knob from front panel by pulling gently, exposing 2 small tap screws
5. unscrew the 2 small tap screws, freeing the switch.
6. NOTE THE EXISTING WIRING! Each terminal has a letter. Take a photo or drawing for reference, because the new switch's post locations were not the same as the old.
7. In my case I had to replace the terminal block kit with a new one. (don't try the aftermarket one's at Home Depot...bad idea event though they say Hotpoint) so I ran those wires first. Easy removal of old, only one wire clip, then fish the wires through. Secure with tap screw at burner location.
8. Hook up the wires. The ones coming from the burner don't seem to matter which one goes to which post but make sure you're replacing them on the posts that the original were on. What I did was just unhook the old posts one at a time and find the corresponding letter on the new one.
9. Break off stem at length of old switch with pliers. make sure you find where off and on are on the switch. Orient the off at the top, then push through from back of range.
10. Screw the 2 tap screws in, securing the switch.
11. Place the orange retainer oriented with flat side the same as the knob, and push the knob back in place.
12. Close lid, replace back panel
13. Insert drip pan/burner into terminal block and secure in drip pan. If your burner plugs are corroded or exposed, replace the burner as it will short out.
14. Plug in to socket and test before pushing range back into place. Read more...
PartSelect Number PS16216966
Manufacturer Part Number WB21X36771
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Scott from Olathe, KS
Front burner would not heat up
1. Pull out range and unplug from socket.2. Lift range lid.
3. Remove back panel. Loosen the 6 - 1/4" nuts, then lift up slightly, which compresses the "latch" at the top middle. Let down and panel comes off easily.
(Note: Do not remove wires yet)
4. Remove control knob from front panel by pulling gently, exposing 2 small tap screws
5. unscrew the 2 small tap screws, freeing the switch.
6. NOTE THE EXISTING WIRING! Each terminal has a letter. Take a photo or drawing for reference, because the new switch's post locations were not the same as the old.
7. In my case I had to replace the terminal block kit with a new one. (don't try the aftermarket one's at Home Depot...bad idea event though they say Hotpoint) so I ran those wires first. Easy removal of old, only one wire clip, then fish the wires through. Secure with tap screw at burner location.
8. Hook up the wires. The ones coming from the burner don't seem to matter which one goes to which post but make sure you're replacing them on the posts that the original were on. What I did was just unhook the old posts one at a time and find the corresponding letter on the new one.
9. Break off stem at length of old switch with pliers. make sure you find where off and on are on the switch. Orient the off at the top, then push through from back of range.
10. Screw the 2 tap screws in, securing the switch.
11. Place the orange retainer oriented with flat side the same as the knob, and push the knob back in place.
12. Close lid, replace back panel
13. Insert drip pan/burner into terminal block and secure in drip pan. If your burner plugs are corroded or exposed, replace the burner as it will short out.
14. Plug in to socket and test before pushing range back into place. Read more...
Your Price
$16.66
In Stock
RCA Range Single Heating Element Support Clip
I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
PartSelect Number PS243701
Manufacturer Part Number WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Paul from Canton, NY
broiling element had burned through, req. its replacement
First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
Your Price
$151.57
In Stock
RCA Range Oven Sensor
SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees to low.
FAILURE POINTS:
There are two logical failure points (1) The oven sensor ( WB21X5301 about $75), or the (2) the controller board (PS238233 about $252). In my case it was the controller board. When replaced the oven worked beautifully.
REPAIR:
As with any repair, you MUST DISCONNECT POWER TO THE UNIT BEFORE SERVICING!!!
Pull oven from the wall:
- Disconnect power by flipping the circuit breaker to the OFF position.
- Remove the top flange / cowling from the top of the oven (it just pulls off)
- Remove two screws under the top flange / cowling
- The whole unit easily slides out, but it is highly recommended that you use two people to place the oven on the floor.
As a diagnostic between these two parts, if the oven sensors measure approximately 1.1K ohms of resistance at room temperature, then it is probably not the sensor. The oven sensor wires are connected to two white wires that run up to the controller board. You need to disconnect the oven sensor to make the measurement. You may either completely remove the oven sensor by cutting the wire (be sure to allow yourself enough slack so that they may be safely reconnected) where it connects to the white wires, OR, (preferred method) if leaving the oven sensor partially installed,
- Remove the top sheet metal cover (10 screws)
- Remove the service connect cover (2 screws - this is where the main Power cord comes into the unit)
- Disconnect the white wires from the controller board (this connector which also includes other circuits is on the left side when looking at the controller board).
- Remove two screws from oven sensor but just let in dangle down so that you can put the sensor in the ice water / boiling water.
Measure the resistance under the following conditions. Your ohm meter should read APPROXIMATELY...
- 1.02K ohms in ice water
- 1.09K ohms at room temperature
- 1.36K ohms in boiling water.
If you get approximately these readings, then it is NOT the oven sensor. If that checks out then re-install the sensor AND the connector.
If it is NOT the sensor, replace the controller board.
- Take a moment to write down the color of the wire to the LETTERING (N, L, G, C / COM,,,) on the controller board. The connectors are in different locations on the new controller board so the wire color to the letter designation is significant.
- Carefully remove the wires one at a time
- VERY carefully remove the keypad ribbon cable from the right side of the controller board.
-- The ribbon cable will disconnect by releasing some little pressure clips on the side of the connector.
- Remove the controller board (4 screws)
- Install new controller board (4 screws)
- VERY carefully connect the keypad ribbon cable on the right side.
-- Make sure that the connector is in the OPEN position first, then,
-- Slide in the cable ensuring that all parts of the ribbon made it into the connector, then
-- Press down on the connector locking tabs.
- Reconnect each wire to the correctly lettering on the board.
-- Again, the connectors MAY BE in a different order on the replacement controller board. Match color to letter.
- Reconnect the (5 wire?) connector that includes the white oven sensor wires.
- Make sure everything looks normal, (i.e. no wires are pinched, remove tools from top of oven area, etc.)
- Re-install top cover.
- Re-install service connect cover.
You can test the unit while it is out of the cabinet,
- Make SURE that all sheet metal covers are in place.
- Flip power breaker to "On".
- Test that oven gets to the desired temp. Read more...
PartSelect Number PS236043
Manufacturer Part Number WB21X5301
It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall. On a newer oven, there may be a fault code displayed. Faulty temperature sensors are often responsible for F3 and F4 error messages on an electric range. Check your manual or the manufacturer website to find out the proper resistance of the temperature sensor. To check your sensor, unplug the oven and use a multi-meter to see if your sensor is at the correct resistance.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
James from Austin, TX
Oven tempature was approximately 150 degrees to low
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees to low.
FAILURE POINTS:
There are two logical failure points (1) The oven sensor ( WB21X5301 about $75), or the (2) the controller board (PS238233 about $252). In my case it was the controller board. When replaced the oven worked beautifully.
REPAIR:
As with any repair, you MUST DISCONNECT POWER TO THE UNIT BEFORE SERVICING!!!
Pull oven from the wall:
- Disconnect power by flipping the circuit breaker to the OFF position.
- Remove the top flange / cowling from the top of the oven (it just pulls off)
- Remove two screws under the top flange / cowling
- The whole unit easily slides out, but it is highly recommended that you use two people to place the oven on the floor.
As a diagnostic between these two parts, if the oven sensors measure approximately 1.1K ohms of resistance at room temperature, then it is probably not the sensor. The oven sensor wires are connected to two white wires that run up to the controller board. You need to disconnect the oven sensor to make the measurement. You may either completely remove the oven sensor by cutting the wire (be sure to allow yourself enough slack so that they may be safely reconnected) where it connects to the white wires, OR, (preferred method) if leaving the oven sensor partially installed,
- Remove the top sheet metal cover (10 screws)
- Remove the service connect cover (2 screws - this is where the main Power cord comes into the unit)
- Disconnect the white wires from the controller board (this connector which also includes other circuits is on the left side when looking at the controller board).
- Remove two screws from oven sensor but just let in dangle down so that you can put the sensor in the ice water / boiling water.
Measure the resistance under the following conditions. Your ohm meter should read APPROXIMATELY...
- 1.02K ohms in ice water
- 1.09K ohms at room temperature
- 1.36K ohms in boiling water.
If you get approximately these readings, then it is NOT the oven sensor. If that checks out then re-install the sensor AND the connector.
If it is NOT the sensor, replace the controller board.
- Take a moment to write down the color of the wire to the LETTERING (N, L, G, C / COM,,,) on the controller board. The connectors are in different locations on the new controller board so the wire color to the letter designation is significant.
- Carefully remove the wires one at a time
- VERY carefully remove the keypad ribbon cable from the right side of the controller board.
-- The ribbon cable will disconnect by releasing some little pressure clips on the side of the connector.
- Remove the controller board (4 screws)
- Install new controller board (4 screws)
- VERY carefully connect the keypad ribbon cable on the right side.
-- Make sure that the connector is in the OPEN position first, then,
-- Slide in the cable ensuring that all parts of the ribbon made it into the connector, then
-- Press down on the connector locking tabs.
- Reconnect each wire to the correctly lettering on the board.
-- Again, the connectors MAY BE in a different order on the replacement controller board. Match color to letter.
- Reconnect the (5 wire?) connector that includes the white oven sensor wires.
- Make sure everything looks normal, (i.e. no wires are pinched, remove tools from top of oven area, etc.)
- Re-install top cover.
- Re-install service connect cover.
You can test the unit while it is out of the cabinet,
- Make SURE that all sheet metal covers are in place.
- Flip power breaker to "On".
- Test that oven gets to the desired temp. Read more...
Your Price
$78.28
In Stock
RCA Range Surface Burner Terminal Block Kit
PartSelect Number PS232606
Manufacturer Part Number WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance before starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Shaohui from East Lansing, MI
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Read more...
Your Price
$20.73
In Stock
RCA Range Drip Bowl - 6 Inch
PartSelect Number PS244364
Manufacturer Part Number WB31M1
This is the drip bowl for your range or cooktop. The drip bowl sits beneath the burner of an electric range and collects any spills during cooking. The bowl is 6 inches in diameter and represents the smaller burner for your range. This product is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Installation Instructions
Jeanette from NATCHITOCHES, LA
6" burner out, 4 horrible looking drip pans.
Remove burners and drip pans, replace with new drip pans and new 6" burner. Reinsert functional burners.
Read more...
Your Price
$81.01
In Stock
RCA Range Broil Element - 240V
PartSelect Number PS249432
Manufacturer Part Number WB44X232
This broil element is found on the roof of the oven and has push-on terminals.
Fixes these symptoms
- Element will not heat
- Little to no heat when broiling
- See more...
Installation Instructions
Donna from Milton, MA
Burned out Broiler Element Needed Replacing
I used a socket set to remove broiler element. It was stiff after so many years, but no problem. All was going well until I pulled too hard on the old element(I'd recommend jiggling if stuck, not yanking) & 1 of the 2 connectors pulled loose & fell behind the back. After my initial panic, I summoned my courage, unscrewed the coverings in the upper back of the stove, found the lost connection, pushed the new element ends through the holes from inside the oven (easiest way to hook it up at this point), plugged it in from the back, pushed it back thru into place inside the oven, reattached everything (front & back), & it worked PERFECTLY! Had I not made a mess of it, it would have taken approx. 5-10 minutes. As it was, it took approx. 15 minutes. EASY!
Read more...
Your Price
$8.50
In Stock
RCA Range Light Lens
PartSelect Number PS1015754
Manufacturer Part Number WB25T10042
Installation Instructions
Gregory from Princeton Junction, NJ
Control switch did not function and one burner worked only occasionally
First, I used the PatrSelect website, which has great prices, and has helpful diagrams. Once I had all the parts, I worked with my wife to turn off the power at our home junction box. Next, I lifted off the cover over the control area of this range. I removed four nuts to lift out the panel that holds the four controls and the fan switch. I removed the wires from the broken controls, removed the two screws holding each control in place, then screwed the new ones in place. I would recommend trimming the posts on the controls to the correct size before screwing them in place, because it is easier to grip them and not bend them when they are not mounted. I reconnected the wires and replaced the panel. For the "receptacle", I followed the instructions provided regarding cutting the wire and placing the wire nut and heat shrink tubing. I opened the unit that houses the burners to get easy access.
Read more...
RCA Range Appliance Types
Related RCA Range Parts
Popular RCA Range Models
Below are the most popular RCA Range models we have. Enter your model number in the search box to find your model.
- BRF725GL9 RCA Range/Stove/Oven Model BRF725GL9 Parts
- L3B155L0L RCA Range/Stove/Oven Model L3B155L0L Parts
- L3U3000L0BG RCA Range/Stove/Oven Model L3U3000L0BG Parts
- L3B115GL0 RCA Range/Stove/Oven Model L3B115GL0 Parts
- L3U30L0 RCA Range/Stove/Oven Model L3U30L0 Parts
- L3B325GL0 RCA Range/Stove/Oven Model L3B325GL0 Parts
