Official Poulan Trimmer Parts

Engine Fuel Filter – Part Number: 530095646

Your Price

$9.16

Poulan Trimmer Engine Fuel Filter

★★★★★

4 Reviews

PartSelect Number PS9285148

Manufacturer Part Number 530095646

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filter is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

Fixes these symptoms

Engine stops after a few seconds or minutes
Will Not Start
See more...

Installation Instructions

Mark from LYNDONVILLE, NY

Deterioration of fuel line system

Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...

Your Price

$9.16

Poulan Trimmer Spark Plug

PartSelect Number PS8996057

Manufacturer Part Number 503235111

Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not part of a kit or assembly. The spark plug is used to ignite the air-fuel mixture inside the combustion chamber. You may need to replace the Spark Plug if your 1 cylinder engine won't start, or if your more-than-1 cylinder engine runs rough. Spark Plugs will wear over time and should be inspected regularly. Customers rate this repair as Easy.

Fuel Line (25" Length) – Part Number: 530069247

Your Price

$12.20

Poulan Trimmer Fuel Line (25" Length)

★★★★★

5 Reviews

PartSelect Number PS9008183

Manufacturer Part Number 530069247

This is the replacement fuel line 25 Inch for several OPE products that use small engines. The fuel line carries fuel from the tank to the carburetor. Over time, the fuel line can become badly clogged, and it can become brittle as well. When the fuel line is badly clogged or cracked, fuel can leak out and it can make it difficult to start or run the engine. To replace the fuel line, carefully disconnect the old line from the carburetor and from the fuel grommet, then replace it with the new line. This fuel line is 25 inches in length and is made of clear plastic. The fuel line is sold individually and is an OEM part sourced directly from the manufacturer.

Fixes these symptoms

Engine stops after a few seconds or minutes
Will Not Start
See more...

Installation Instructions

Mark from LYNDONVILLE, NY

Deterioration of fuel line system

Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...

Your Price

$18.34

Poulan Trimmer Purge Line

★★★★★

2 Reviews

PartSelect Number PS9008180

Manufacturer Part Number 530069216

This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.

Fixes these symptoms

Engine stops after a few seconds or minutes
Will Not Start
See more...

Installation Instructions

Mark from LYNDONVILLE, NY

Deterioration of fuel line system

Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...

Your Price

$6.40

Poulan Trimmer Filter

★★★★★

1 Review

PartSelect Number PS9005902

Manufacturer Part Number 530150253

The air filter prevents dirt and debris from entering the engine on your lawn equipment. This is an OEM filter that is white, roughly 2x3.5 inches in dimension, and can only be purchased individually. Made of foam, the air filter becomes clogged and worn over time, causing the engine to run rough from restricted air flow. You can make this repair easily with no required tools by inserting the new filter inside the air cleaner housing of your engine.

Your Price

$15.27

Poulan Trimmer Fuel Line

PartSelect Number PS9008192

Manufacturer Part Number 530069599

This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line wear out to the point of breaking, cracks and/or leaking will appear and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Steve from SALEM, OH

Broken fuel line

Removed broken fuel line from gas tank. Threaded new line into tank routed it to the carb and cut to length needed. Attached to the carb. Read more...

Your Price

$12.20

Poulan Trimmer Purge Bulb

PartSelect Number PS9003852

Manufacturer Part Number 530047721

This primer bulb, also known as a purge bulb, is used to push more fuel from the fuel tank into the carburetor of your small engine equipment, to help the engine start easier. Over time and through extended use and exposure to gas and oil, the bulb of the primer will eventually lose its elasticity and crack or break. This bulb is made of plastic and can be replaced by accessing the ignition system. Disconnect the fuel lines and pop out the bulb with a set of pliers, and once you pop in the new bulb, you just reconnect the fuel lines. This bulb is compatible with a variety of makes and models of small engine equipment and is sold as an individual part.

Installation Instructions

Robert from MANVILLE, NJ

Replace the fuel lines

Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose.

Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through. Read more...

Trimmer Carburetor Kit – Part Number: 545081848

Your Price

$55.63

Poulan Trimmer Carburetor Kit

★★★★★

1 Review

PartSelect Number PS9030700

Manufacturer Part Number 545081848

This carburetor rebuild kit (part number 545081848) is for lawn and garden equipment engines. Carburetor rebuild kit 545081848 includes gaskets and parts for rebuilding the carburetor. Work in a well-ventilated area and drain the fuel from the tank and fuel lines before rebuilding the carburetor

Line Trimmer Mow Ball – Part Number: 532182217

Your Price

$38.50

Poulan Trimmer Line Mow Ball

PartSelect Number PS9013718

Manufacturer Part Number 532182217

This is a manufacturer approved mow ball assembly used on some Wheeled Trimmers. Mow ball assembly prevents the trimmer from scalping the grass. This Assembly includes the Plastic Housing, Ball Bearing and a Retaining Ring. Please note Bolt used to attach this assembly is Sold Separately.

Fuel Line Fitting – Part Number: 530023877

Your Price

$7.63

Poulan Trimmer Fuel Line Fitting

★★★★★

1 Review

PartSelect Number PS9003834

Manufacturer Part Number 530023877

The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Mark from LYNDONVILLE, NY

Deterioration of fuel line system

Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...

Shop by Department

Top Appliance Brands

Top Lawn Equipment Brands

Poulan Trimmer Parts

Popular Poulan Trimmer Parts

Poulan Trimmer Appliance Types

Related Poulan Trimmer Parts

Popular Poulan Trimmer Models

Shop by Department

Top Appliance Brands

Top Lawn Equipment Brands

Sample Model Number Tags

EasyApplianceParts is Now PartSelect!

Poulan Trimmer Parts

Find Your Part

Popular Poulan Trimmer Parts

Poulan Trimmer Appliance Types

Related Poulan Trimmer Parts

Popular Poulan Trimmer Models