This genuine replacement part is sourced directly from original manufacturer. It is used on a variety of lawn mowers. This is the knob that helps to secure the upper handle. It is made out of plastic and it is sold individually. When replacing this know you will need a screwdriver for the screw securing the knob.
This is a manufacturer approved mow ball assembly used on some Wheeled Trimmers. Mow ball assembly prevents the trimmer from scalping the grass. This Assembly includes the Plastic Housing, Ball Bearing and a Retaining Ring. Please note Bolt used to attach this assembly is Sold Separately.
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.
This drive control cable is a high quality replacement part that is sourced from original equipment manufacturer for use on high wheeled trimmers. The control cable stops the blade when the control handle is released, if the cable is broken it will cause the brake to not release even when the lever is pressed. Please note one durable rubber insulated cable is included per order.
This is a genuine manufacturer sourced replacement mow-ball designed for use with wheeled trimmers. It acts as a cover for the carrier plate and it allows for the unit so move smoothly. It is made out of black plastic material and it is sold individually. You would need a wrench to replace this cup.
This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw.
This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair.
Customers rate this repair as Easy.
This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Craftsman lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and use of this item. This part is made of h...Read moreigh-quality metal and it is sold individually, you will need a wrench to secure or remove it.
This replacement belt is a genuine item that is sourced directly from original equipment manufacturer. It is commonly used v-belt for high wheeled trimmers. This is the the main belt that drives the cutter head. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. This part is made out of rubber ma...Read moreterial and it is sold individually. To complete this repair you will need a set of wrenches and a screwdriver. • First remove screw at front of chassis cover • Lift cover up and away from trimmer • Remove the two (2) screws on sides of trimmer securing the debris shield • Turn trimmer on its side with carburetor and fuel cap up • Remove the two (2) screws on under-side of trimmer securing the debris shield • Slide the debris shield rearward and remove • Remove belt from engine pulley on crankshaft • Remove belt from trimmer head pulley • Note the position of the control cable and idler return spring • Remove idler assembly from chassis and re-move belt and idler from trimmer • Remove belt from idler assembly by removing bottom belt keeper and idler pulleys • Assemble new belt, idler pulleys and bottom belt keeper to idler bracket • Tighten pulley bolts securely • Position belt and idler assembly in trimmer, reconnect idler spring and reattach idler to chassis
A genuine item that is supplied by the original equipment manufacturer for use with lawn and garden equipment. It is a high-quality screw which has a few different applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and application of this hardware. Keep in mind this durable metal component is sold individually.
This is an original replacement part supplied from original equipment manufacturer. This bolt is designed to safely secure the mow ball assembly on a wheeled trimmer. To complete this repair you would need a socket wrench in order to remove/install this bolt. Includes one (1) bolt per order.
This is a genuine replacement bottom deflector which is supplied by the original equipment manufacturer for use with handheld trimmers. It is mounted over the cutting head assembly in order to direct the trimmings away from the user and provide the protection from the string while operating the equipment. This high-quality component is ma...Read morede of durable black plastic and it is sold individually, please note the hardware to secure it is sold separately.
This is a manufacturer approved replacement part designed for use with high wheeled trimmers. This carrier plate acts as a trimmer head/housing which secures the trimmer line. It is made out of metal and it is sold individually. Please note the locking plate/tab is sold separately. To complete this repair you would need a socket wrench to remove the bolt which holds the assembly to the jackshaft.