Poulan Trimmer Engines

Poulan Trimmer Piston Ring

★★★★★

★★★★★

2 Reviews

This OEM Piston Ring is used to provide a seal between the piston and cylinder wall. It attaches around the piston, inside the groove. It will require a screwdriver, allen wrench, torx wrench and socket set and is rated as "Hard" to install. The part is silver, metal, and individually sold. If broken due to general wear/fatigue you will have poor compression within the cylinder, causing a loss of power. If broken, damaged or worn, the part should be replaced. Refer to your make, model, and diagram to ensure this is the correct part.

Poulan Trimmer Piston Cylinder Assembly Kitinder Kit This is a genuine OEM replacement part used with several lawn trimmer devices. The piston/cylinder kit is composed of metal and plastic, and is fitted between the crankshaft assembly and the gasket foam kit. It is recommended to refer to engine manual and diagrams for further instruction. The piston/cylinder kit is sold individually. To complete the repair, you will need a screwdriver, pair of pliers and a socket set.

Poulan Trimmer Piston Ring This genuine manufacturer sourced replacement part is specially made for use with a variety of handheld lawn and garden equipment. This part is installed on top of the piston/connecting rod. Its purpose is to create a seal in the cylinder so that it can build pressure. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase, causing low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. Includes one (1) metal piston ring. Tools Required: Receptacle for draining fuel, Torx wrenches, spark plug wrench, 10mm wrench (or adjustable), long-nosed pliers, rubber mallet, standard screwdriver, old starter rope (or similar cord), adjustable pliers, 2-cycle engine oil, razor blade, ignition gapping gauge. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring

Poulan Trimmer Piston Ring

★★★★★

★★★★★

1 Review

This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine maintains the pressure it needs to run. If the piston ring is damaged, oil can seep into the combustion chamber, causing your engine to exhibit rough idling and your machine emit blue smoke. To switch out a defective piston ring, detach the old ring from the piston with a screwdriver. When installing the new ring, you may need to compress it to make it fit properly. Please be aware that this genuine OEM replacement part is bought individually. It is recommended that you replace all the piston rings in your machine at once, as they tend to wear down at the same rate. Carefully review your user manual to determine how many rings your machine needs before placing your order.

Poulan Trimmer Kit - Piston This piston kit is a genuine OEM replacement designed for small 2-stroke engine equipment. It includes the components needed to restore proper compression and dependable engine performance during a top-end rebuild. Manufactured for precise fit and durability, it’s an ideal replacement when worn pistons or rings cause power loss, hard starting, or reduced efficiency.

Poulan Trimmer Jackshaft This is an authentic OEM part four use with Husqvarna, Poulan, Weed Eater Trimmers. The shaft rotates the cutting head on the line trimmer. The most common reason for replacing the shaft is if it is damaged or if the trimmer head will not rotate. This part is sold individually. The tools that you will need to replace the shaft are a T-25 Torx head screwdriver and a 7/16 inch wrench.

Poulan Trimmer Cylinder Head This is an original replacement part manufactured for outdoor power equipment. The cylinder is used to house the piston and spark plug and is used to provide a combustion chamber to ignite the air-fuel mixture. This cylinder is available as an individual replacement part, please see model diagram for associative parts.

Poulan Trimmer Piston This is a genuine OEM approved replacement part designed for use with Hitachi nailers. The piston is a central component of an engine. It both provides compression within the engine, as well as transfers the energy from combustion to the crankshaft (which creates rotation). This assembly includes the metal piston, ring, two retainers and the pin. Replacing the piston assembly is not the simplest repair, but it is definitely something you can do yourself. You will need a screwdriver to remove the cover and a set of sockets and wrenches for the rest of the repair.

Poulan Trimmer Kit-piston/cyl.

Poulan Trimmer Piston Ring This is an authentic OEM sourced replacement piston ring which is specially designed for use with Poulan gas powered trimmers. The purpose of this part is to provide a tight seal between the cylinder and the piston. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase, causing low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. Please note this high-quality part is made of durable metal and is sold individually.