My Orders
Hose Clamp WP285655
Official part for Kenmore, Whirlpool, Maytag, Amana
Fits your ADB1400AGS3!
About This Part
What it does. Why it matters. Everything you need to know for an easy fix.
Hose Clamp Specifications
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Part #WP285655
Manufactured by
Whirlpool
for Kenmore, Whirlpool, Maytag, Amana
You May Also Need
Because heroes deserve fewer surprise re-installs.
$46.34
In Stock
$20.36
Special Order
Affresh Dishwasher Cleaner Tablets - 6
Part #W10549851
$22.52
In Stock
Affresh Washing Machine Cleaner Tablets – 6 Count
Part #W10501250
$28.42
In Stock
$18.22
On Order
$27.36
In Stock
Refrigerator Deodorizer
Part #MCS62101805
$31.58
In Stock
Genuine OEM: Original Parts. Lasting Repairs.
Because quality isn't optional.
OEM stands for Original Equipment Manufacturer. This means that the company who made your appliance is also supplying the replacement part.
| Features | OEM | Generic |
|---|---|---|
| Genuine brand name | ||
| Guaranteed to fit | ||
| Superior Quality | ||
| Long term value |
Part Videos
Watch our pros, then fix it yourself.
Replacing your Kenmore Washer Hose Clamp
Repair Tips
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
Sort by:
- Prev
- 1
- Next
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sorry, we couldn't find any existing installation instruction that matched.
Cracked hose AGAIN!
9 of 21 people
found this instruction helpful.
Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.
Other Parts Used:
Was this helpful?
Thank you for voting!
Water leak noted on floor at front of washer and at sides
58 of 66 people
found this instruction helpful.
Occasional noted leak became worse and I had a repair service out. Incorrect detection of outer tub seal made so cancelled them and read comments about raising the top. Did so just at start of a rinse cycle to see soapy water shoot from top of syphon break then continue to dribble out through tub empty process--this is what had cause th
... Read more
e water to flow down the interior drain hose and out through the side and bottom near the pump.
Ordered all the parts shown here and they arrived just in time for planned work. Did not need or use the clamp and gasket purchased as the gasket was included in the break package and I really like the old-style clamps much better.
Replaced the break and the elbow and put it back together. Things went south on a rinse as water shot out the back hose at the new elbow. I had not realized the size of the new elbow was smaller than the original. Went back to the old elbow but it bothered me that it would still move when the 4 assembly bolt-screws were completely tight.
So far this seems to have worked. There does not seem to be any leaking at all. For those who read this, the job could be done in about and hour for less than I spent if you observe and diagnose properly. It appears that the washer at the end of the Syphon Break wore out and that is what caused the leak.
Thanks much to PartSelect for being in business and to all the posters on this site for helping everyone to get these things done right!
Ordered all the parts shown here and they arrived just in time for planned work. Did not need or use the clamp and gasket purchased as the gasket was included in the break package and I really like the old-style clamps much better.
Replaced the break and the elbow and put it back together. Things went south on a rinse as water shot out the back hose at the new elbow. I had not realized the size of the new elbow was smaller than the original. Went back to the old elbow but it bothered me that it would still move when the 4 assembly bolt-screws were completely tight.
So far this seems to have worked. There does not seem to be any leaking at all. For those who read this, the job could be done in about and hour for less than I spent if you observe and diagnose properly. It appears that the washer at the end of the Syphon Break wore out and that is what caused the leak.
Thanks much to PartSelect for being in business and to all the posters on this site for helping everyone to get these things done right!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Drive Pump Leaked
73 of 90 people
found this instruction helpful.
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer an
... Read more
d remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
- Prev
- 1
- Next
DIY Questions and Expert Answers
4 questions answered by our Repair Experts.
Ask our experts a question about this part and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
- Prev
- 1
- Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charles
- For model number wtw8240ywo
October 24, 2019
Have a leak clean all the water up on floor, is dry wash cloth now don't see no water floor is dry
Hi Charles, we cannot be 100 percent certain what is causing the issue. The hose clamp part WP596669 is our best guess as to what would fix your problem. Thank you for your question and good luck with your repair!
2 people
found this instruction helpful.
Was this helpful?
Thank you for voting!
Tim
- For model number MAV208DAWW
November 21, 2021
Spin cycle has slowed down. Is there a clutch on this model?
Hello Tim, Thank you for the question. This model does not have a clutch. We suggest checking the Drive Belt for wear and the Transmission Pulley and Bearing Kit. We hope this helps!
$45.29
In Stock
$16.07
In Stock
1 person
found this instruction helpful.
Was this helpful?
Thank you for voting!
Merrill
- For model number mvwb835dw1
January 8, 2018
How do i remove the cabinet on this model of Maytag washer? I have a leak and i can't get the cabinet off to determine where the leak is coming from. It might be something as simple as a hose clamp, but i'm not smart enough to determine how to remove the cabinet. Any and all help will be greatly appreciated. Thanks for your time.
Hi Merrill,
Thank you for your question. There is a video on our website that you can reference on how to remove the cabinet. The washing machine in the video may not show exactly like the one you have and the part being installed is the clutch assembly, but it will show you how to remove the cabinet. You will find the video under part number PS334641. I hope this helps. Thank you and have a great day!
1 person
found this instruction helpful.
Was this helpful?
Thank you for voting!
Jose
- For model number mhw5500fw1
January 22, 2023
the water inlet do not stop hot and cold even when not workig the whasher
Hi Jose, thank you for reaching out. If your washer water inlet valve would not shut off, there are a few possible causes: damaged water inlet valve, broken water level switch, or issue with the hose clamp. We suggest that you check these parts and replace the damaged component to resolve the issue. If you require assistance to place an order, please contact customer service. We hope that helps!
$111.43
In Stock
$7.47
In Stock
$49.50
In Stock
Was this helpful?
Thank you for voting!
- Prev
- 1
- Next
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.