- Home
- ZDIS15CSSN
- Instructions
ZDIS15CSSN General Electric Ice Maker - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken light switch
0 of 1 people
found this instruction helpful.
-
Atlee from Jupiter, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones
Was this helpful?
Thank you for voting!
loud noise coming from back of fridg.
-
William from Fort Mohave, AZ
- Easy
- 15 - 30 mins
-
Nutdriver
Unplug A C Cord . Simply unscrewed lower back cardboard cover panel and unscrewed condenser fan motor , removed wiring plug , pulled fan motor out removed fan blade and put it on new motor . then I Reinstalled motor. Noise is gone . EASY INSTALLATION .
Was this helpful?
Thank you for voting!
Condenser fan made loud noise.
-
Robert from Perrysburg, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
Watched the video that was attached to my order confirmation (great idea) and just followed it step by step. Real easy repair since I had tried to fix the noise first without ordering parts, so I knew what I was doing Did a temporary fix which quieted it down while I waited for the parts and then the repair itself was pretty straight fo
... Read more
rward.
Read less
Was this helpful?
Thank you for voting!
Condenser Fan Motor had stopped working
-
Marshall from Garland, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I found the part I needed on this website, watched the tutorial and saw how simple it was to do myself. I ordered the part and it arrived within a few short days. It took me no more than 15 minutes to change out the part. I saved myself several hundred dollars. It is rather shocking how much the "professionals" charge considering the cost
... Read more
of parts, labor and nominal service fees.
Read less
Was this helpful?
Thank you for voting!
refrigerator not cold. and keeps striping the circuit breaker and shutting off other appliances using the same circuit.
-
kevin from Antelope, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
what I discovered is the condenser fan is still operating but not strong another word insufficient cooling for the condenser. therefore, it's getting too hot and shutting off and stripped the circuit breaker. After installing the new condenser fan, it gets back in business. it's quite simple. Just unplug the unit off, uncover the bottom b
... Read more
ack cover and there you see compressor, condenser fan and other good stuff. there you unscrew the nut in front of the condenser fan and remove the fan, then it expose the two screws that holding the fan motor, remove these screws and take out the motor. and just install the new fan motor kit in and there you have it. plug it back to the wall and there it goes
Read less
Was this helpful?
Thank you for voting!
Very noisy when condensor fan came on
-
manuel from wilmington, DE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I've tried ordering the part from Sears and they told me it will take about 7 days for the part to arrive, some other place said it will overnite for extra money. So I've ordered the part from Part Select at a good price and prompt delivery. once the part arrive installing the part so so easy cause it had easy to follow instructions.
Was this helpful?
Thank you for voting!
No water running across the evaporate plate
-
Scott from Las Vegas, NV
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Since no ice was forming on the evaporator plate, I first checked to see if I was getting water. Water to reservoir was fine, but it was not moving from the reservoir. Pretty logical that something was wrong with the pump. I pulled pump out. It was locked up, with a significant amount of calcium buildup. Replaced it and all works fin
... Read more
e. Great ice again.
Read less
Was this helpful?
Thank you for voting!
our ice maker was not cutting the ice into squares.
-
Scott from Phoenix, AZ
- Easy
- 15 - 30 mins
-
Nutdriver
I determined it was the cutter grid because there was a broken wire on the existing one. They have to heat up and cut the ice. I ordered it and the part was at my house in 1 day. The cutter grid part was easy to install. The ice maker is working great now.
Was this helpful?
Thank you for voting!
Inlet water valve restricted with debree.
-
Michael from Clanton, AL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Open appliance door. Removed access plate at lower front (two screws). Removed two screws holding valve in place. Depressed water line retainers and removed water lines from valve. Inserted water lines in replacement valve, remounted valve, reinstalled access plate. Tested operation. (I did install a water filter during the repair to prev
... Read more
ent reoccurrence.)
Read less
Was this helpful?
Thank you for voting!
macnine was producing ice but would not cut into cubes
-
ALAN from KENNETT, MO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
remove the front cover by removing two screws. then remove two screws with a nut driver on each side. unplug the wireing harness from the top of the unit (may need pliers for this) the pull the unit out. then slide the new unit in, connect the wireing harness, install two side screws, and install the front cover and wham you will hav
... Read more
e ice in about 30 minutes. thanks parts select. you were very easy to deal with
Read less
Was this helpful?
Thank you for voting!
Fan became noisy and started wobbling.
-
James from Cave Creek, AZ
- Really Easy
- 15 - 30 mins
-
Socket set
UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the scre
... Read more
ws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.
Read less
Was this helpful?
Thank you for voting!
Condenser Fan was making noise
-
Kerry from Franklin, TN
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to instal
... Read more
l the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.
Read less
Was this helpful?
Thank you for voting!
noise coming from back of refrigerator. determined it was the fan
-
BRUCE from SOUTH WINDSOR, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nu
... Read more
t driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.
Read less
Was this helpful?
Thank you for voting!
Old fan housing broke
-
Michael from Pinedale, WY
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.
Was this helpful?
Thank you for voting!
Condenser fan vibrated loudly while turning
-
Robert from Aurora, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simpl
... Read more
y replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)
Read less
Was this helpful?
Thank you for voting!