- Home
- ZDIS15CSSN
- Instructions
ZDIS15CSSN General Electric Ice Maker - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The wires in the cutter grid assembly were briken
5 of 5 people
found this instruction helpful.
-
Tony from HOUSTON, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced the assy. But, I would have been happier if you sold just the wires. I could have replaced the wires at a much lower cost and may have taken less than an hour to replace the wires.Still happy - the ice maker works.
Was this helpful?
Thank you for voting!
water leaked when the paddel was pushed
6 of 8 people
found this instruction helpful.
-
Monica from EDMOND, OK
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
Was this helpful?
Thank you for voting!
Water valve leak
8 of 15 people
found this instruction helpful.
-
Frank from Fairmount, GA
- Really Easy
- Less than 15 mins
-
Socket set
Unbolted valve from wall. Unplugged electical connection then unplugged two water lines by pulling them out of valve. Put in new valve-reinserted electrical plug and water lines. Bolted new valve back to wall.
Was this helpful?
Thank you for voting!
The tunes were moldy and the pump didn't work.
5 of 7 people
found this instruction helpful.
-
Gerald from ELMHURST, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the
... Read more
screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lights not working some times
4 of 5 people
found this instruction helpful.
-
Harry from COLUMBIA STA, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed old switch and installed new - but did not solve problem
Was this helpful?
Thank you for voting!
condenser fan making growling noise
4 of 5 people
found this instruction helpful.
-
Mark from Green River, WY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that
Was this helpful?
Thank you for voting!
Noise when compressor was running
7 of 14 people
found this instruction helpful.
-
John from Medina, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver
I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the brac
... Read more
ket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!
Read less
Was this helpful?
Thank you for voting!
fan bearnings wornout
4 of 5 people
found this instruction helpful.
-
Thomas from Grand Island, FL
- Really Easy
- 15 - 30 mins
-
Socket set
Simple remove the fan and motor, plug in the new cord and screw in the new motor.
Was this helpful?
Thank you for voting!
Ice maker Thermostat not shutting off the making of ice
3 of 3 people
found this instruction helpful.
-
M Edward from Timonium, MD
- Very Easy
- Less than 15 mins
-
Nutdriver
un screwed the hex screw holding the thermostat and installed the new thermostat and pluged the new part int its place. I undid the front shield so i could get to the plug.
Was this helpful?
Thank you for voting!
Loud noise coming from rear of fridge.
3 of 3 people
found this instruction helpful.
-
Gerardo from Berwyn, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
It was very easy. The part make look different online but it was a proper replacement.
Was this helpful?
Thank you for voting!
Excess ice
3 of 3 people
found this instruction helpful.
-
Michael from WATCHUNG, NJ
- Really Easy
- 15 - 30 mins
-
Pliers
Double check the actual part number. While the item looks the same, my unit had a 3 prong plug while the replacement had only 2 and did not fit.
Was this helpful?
Thank you for voting!
Overflow pump-cutting grid wire & spacers
3 of 3 people
found this instruction helpful.
-
Leonard from ALVARADO, TX
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Replaced pump-loop cutting grid wire loosely around spacers-hold loose end with pliers-working from back to front remove all slack. Pull until piano string tight. Wire will not break if not linked. Tighten front screw.
Other Parts Used:
Was this helpful?
Thank you for voting!
a rumbling noise was comming from the back of the fridge
3 of 4 people
found this instruction helpful.
-
Craig from Birchwood, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembl
... Read more
y,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket
Read less
Was this helpful?
Thank you for voting!
Condenser motor was making noise.
4 of 8 people
found this instruction helpful.
-
Joe from Spring Hill, TN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Socket set
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.
Was this helpful?
Thank you for voting!
replaced motor and fan
3 of 5 people
found this instruction helpful.
-
Rex from Amarillo, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.
Was this helpful?
Thank you for voting!