- Home
- ZDIS15CSSN
- Instructions
ZDIS15CSSN General Electric Ice Maker - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Kit did not match up to existing bracket
-
John from Severna Park, MD
- Difficult
- 30 - 60 mins
-
Nutdriver, Socket set, Wrench (Adjustable)
fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)
Was this helpful?
Thank you for voting!
fridge started making an awful noise...still worked but noise occurred when fan kicked on
-
Diane from Rocky Mount, NC
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
My husband watched the video on the repair and followed it step by step...works like a charm! The repair shop wanted 299.55 to fix it - the part was 79.00....big savings by doing it ourselves.
Was this helpful?
Thank you for voting!
Noisy/Failing Condenser Fan
-
Craig from Tomah, WI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Unplugged the refridgerator and pulled the rear cover. Had to take the fan blade off in order to get at the screws holding the existing motor in place. Removed the old fan. Pressing the new plastic fan onto the new motor shaft was a little more effort than expected, but I guess it won't come off. I have large hands so mounting the new
... Read more
unit was a little bit of a challenge getting the small screws started. Once the three screws were tightened all I had to do is plug the electrical connector in and replace the rear cover. I was happy that the existing electrical connector was the right one for the new motor too, and that I didn't have to use the provided wire harness. All in all the repair went pretty well.
Read less
Was this helpful?
Thank you for voting!
Condenser Fan quite
-
Jennifer from San Antonio, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I tried WD40, it worked for a day. Got a new part from PartSelect.com and was a good brand. Panasonic. Easy fix and works great. Saved a bundle. I priced a new fridge, no way, this was better. Thank you Partselect.
Was this helpful?
Thank you for voting!
Light switch inoperative
-
Timothy L from Middlebourne, WV
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again
... Read more
it would probably take me half as long.
Read less
Was this helpful?
Thank you for voting!
No problem
-
Ordean from Minot, ND
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set
The repair went just fine. Your instruction regarding using the wiring harness were clear. Most of all I am happy to not have to listen to a noisy motor all night.
Was this helpful?
Thank you for voting!
refrigerator on and off
-
Anthony from Culpeper, VA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
as told per compter
Was this helpful?
Thank you for voting!
Refrigerator motor quit
-
Wendi from Lubbock, TX
- Really Easy
- 30 - 60 mins
-
Socket set
Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source
Was this helpful?
Thank you for voting!
replacing condenser fan motor
-
Norman from Azle, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Socket set
Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Grea
... Read more
t to hear a quit running refrigerator again.
Read less
Was this helpful?
Thank you for voting!
My undercounter ice machine grid cutter wire broke
-
Ronnie from Corpus Christi, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the two screws that hold the shield in front of the grid and put them aside allowing access to the grid. I then removed the two screws that hold the grid in place. I unplugged the connector and then pulled it out. I reversed the process to reassemble and powered up the unit. I now have ice again. This whole process probably
... Read more
took me 15-20 minutes to do the install.
Read less
Was this helpful?
Thank you for voting!
Water was not circulating onto freezing plate
-
doug from atlanta, GA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
Simple, remove water reservoir (2 screws). Remove pump cover (1 screw). Remove 2 screws on bracket holding pump and unplug pump. My wiring was somewhat corroded and it took a bit of pulling to unplug. When you replace with new motor make sure to snap in new plug snug or it will not start up. Reassemble and away you go.Making ice no proble
... Read more
m.
Read less
Was this helpful?
Thank you for voting!
Wire in ice cutter assembly had broken
-
Paul from Metairie, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed old assembly by disconnecting 2 wiring harness connections and loosening 2 screws with nutdriver. Installed new assembly using same process. Had ice in about an hour. Very easy.
Was this helpful?
Thank you for voting!
Loud fan motor
-
Brian from Saint Augustine, FL
- Easy
- 15 - 30 mins
-
Nutdriver
Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.
Was this helpful?
Thank you for voting!
fan motor
-
James from Kennett, MO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
I watched the film on installing and taking out. Step by step. easy.
Was this helpful?
Thank you for voting!
Recent move and movers broke the light switch on refrigerator side.
-
Carl from Warsaw, MO
- Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will dro
... Read more
p down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!
Read less
Was this helpful?
Thank you for voting!