TPX21PRSAWW General Electric Refrigerator - Instructions

First I turned the freezer off and took out all of the shelves in the freezer section. I then removed the guides that the shelves go into. I removed these only from one side of the freezer - the left side actually. Now I removed the plastic piece that keeps the bulb in the freezer protected. Removed the bulb. Removed the three screws on t ... Read more he top and the two in the bottom that keep the rear panel of the freezer attached. This exposed the header cable and the coils. The coils had ice on the lower section, I used a hair dryer to melt the ice. Removed the cable assembly that has the two heater elements and the thermostat. The thermostat had to be plucked off the the metal pipe of coils. Replaced the assembly with the purchased assembly. Clipped the thermostat onto the metal pipe of the coils. COnnected the wires at the white connector. Attached the real panel using the five screws, put the bulb back in, installed the bulb cover, installed the shelf guides, put the shelves back in.

Freezer freezes very well now.

First I removed the face plate by lightly prying . Once removed noticed 4 screws. Removing the screws allows you to gain access to the two plugs, one for the solenoid and the other for the switch that energizes the solenoid . Unplug the connectors and carefully lower the piece enough to reach the 3 screws that hold the solenoid in place. ... Read more The 4th screw in the center at the bottom of the solenoid is the ground wire. If it is rusted like mine was just re-attatch it to one of the solenoids holding screw. It must be grounded!
Just re-assemble, just dont forget to replug the connectors. Also a little hint, If you open the freezer door a little you wont trigger the solenoid.

The repair is easy, just pop the grill off around the ice and water door, then there are 4 screwws to take out so the touch pad can be moved out of the way to unsnap the old door assm. and snap in the new one and wait about a year and a hald to order another one!!!!!

Shut off power to the refrige. Removed old icemaker, using large hammer. Installed new unit.

First i unpluged the power then cleaned everything out of freezer and removed all the drawers and racks them removed the 2 screws at bottem of freezerand removed panel then removed 4 screws on the bulbs and unpluged the wire and took off the sensor and replaced with new one put everthing back. Then on the top of refigerator side on the t ... Read more op behind the adjuster is the defrost timer pulled handle out and off removed plastic shield and removed 2 screws and unplug the timer and change it then put everything back and pluged back in and everything worked in a few minutes

This is a sibe-by-side refrigerator/freezer that needed a new lower hinge set for the fridge door.

First I removed everything from inside the fridge door, closed it, then loosened the top hinge bolts with an 8mm socket on a 1/4-inch ratchet. Using an 8mm nutdriver, I removed one bolt and loosed the other just far enough to be ... Read more able to lift the hinge and swing it out of the way. (These bolts are long. The nutdriver is faster than the ratchet but you need a ratchet or a wrench to first break them loose.) Then I just lifted the door off the bottom hinge and set it aside.

The plastic lower front grill was covering the lower hinge but that grill is just held at the ends by spring clamps -- popped off easily so I could get to the hinge bolts. Again, 8mm bolts, just remove & replace hinge. I also had to replace the upper half of the door closer cam, which is screwed to the bottom of the door, being careful that the holes lined up: cam, shim, door holes.

Now the tricky part was lifitng the door back on the lower hinge. (It helps to have an assistant at the bottom to locate the hole for you.) Once the door was up, I swung the top hinge over, ran the two bolts in finger tight with my nutdriver, checked & adjusted the spacing* of the fridge door and tightened the bolts. This was all very easy! (*^_^*)

*On a side-by-side, you'll want the door to be straight up & down with a consistent gap top to bottom with the freezer door. The hinge has some slack for adjustment by positioning the door, then tightening the bolts. You'll see what I mean.

The icemaker's valve is easy to inspect and test. First, gently pull the refrigerator away from the wall, and unplug it. Turn off the water supply to the icemaker by closing the shut-off valve in the copper waterline leading to the valve. Use a screwdriver or nutdriver to remove the rear lower access panel from the refrigerator's back. ... Read more r />
Next, remove the fill tubing from the water valve. Use a wrench to loosen the flare nut on the brass fitting on the inlet side of the valve (above). Place a container or towel under the valve to catch the small amount of water that will spill from the valve and tubing.

Now use a screwdriver or a nutdriver to remove the screw holding the valve's mounting bracket to the refrigerator cabinet. Pull the valve out of the compartment and remove the tube (or tubes if both water dispenser & ice maker) on the valve's outlet. If plastic tubes don't come out with pliers and assuming there is enough extra tubing, then cut the plastic tubing with a even straight cut edge razor. Then, remove the solenoid's electrical contacts.

Push the plastic water and ice tubes int he appropriate holes in the new valve outlet, reconnect solenoids and remount new water valve.

Before installing the back panel on the refrigerator cabinet, test run the icemaker. Look for leaks, and tighten any leaky connections. If necessary, use Teflon tape or a similar product to ensure tight connections. Discard the first ice cubes that are produced because they are likely to have sediment in them.

Read less