TES335MB5 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven not heating properly
0 of 1 people
found this instruction helpful.
-
Matthew from Greenville, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplug the oven, pull it out and empty the inside of the oven. The bottom heating element just unscrews from the back of the oven with two screws. Pull it out from the back of the oven and gently pull off the electrical connections. Reattach them to the new heating element, put it back into the oven and reattach the screws. Turn the o
... Read more
ven on and check to make sure that the new heating element is working. Put everything back in the oven and you're done!
Read less
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people
found this instruction helpful.
-
Shirley from Las Vegas, NV
- Really Easy
- Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people
found this instruction helpful.
-
William from Schwenksville, PA
- Easy
- Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!
light bulb went out in my oven
2 of 7 people
found this instruction helpful.
-
Janet from Ada, MI
- Really Easy
- Less than 15 mins
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this helpful?
Thank you for voting!
door glide broken
0 of 1 people
found this instruction helpful.
-
David from Port Orange, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
removed the old ones.then installed the new ones.
Was this helpful?
Thank you for voting!
Switch had burned out due to faulty wiring by electrician when appliance first installed
1 of 4 people
found this instruction helpful.
-
Doriss from Cartersville, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
my son simply replaced the switch, so now I have a working oven light once again
Was this helpful?
Thank you for voting!
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
0 of 2 people
found this instruction helpful.
-
Joanne from Negaunee, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
water pump went out
2 of 12 people
found this instruction helpful.
-
paul from windsor, VA
- Really Easy
- Less than 15 mins
-
Pliers
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
Replacing the Upper Spray Arm, part # PS2581378
-
Vittorio from Wakefield, MA
- Really Easy
- 15 - 30 mins
The detection of the part and the replacement of the upper spray arm was quite easy, because of its unique shape and function, and also because it was easy to screw in place. I saved the web order page in case this part tends to deteriorate frequently, even though it is the first time it showed this problem since we purchased this applian
... Read more
ce.
Read less
Was this helpful?
Thank you for voting!
Side trim broke
-
Paul from Adamsville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.
Was this helpful?
Thank you for voting!
Terminal Block was melted where the cord had came lose.
-
Louise from Humansville, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this helpful?
Thank you for voting!
Burner Would,Nt Heat Up.
-
david from cleveland, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed top of stove replaced heating element ,piece of cake.
Was this helpful?
Thank you for voting!
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
-
Joseph from Channelview, TX
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
R&r
Was this helpful?
Thank you for voting!