EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

SDL20KCSBBS General Electric Refrigerator - Instructions

All Instructions for the SDL20KCSBBS
61 - 75 of 542

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Dispenser not working
9 of 11 people found this instruction helpful.
  • David from Boca Raton, FL
  • Difficult
  • Less than 15 mins
  • Pliers, Screw drivers
As it turned out much of the electronics is driven by 13.5 volts off the Main Control Board. The Ice Dispenser caused the problem because it over currented the depleted board power. You could hear a clicking noise from the board which was the main relay short cycling and not staying energized. While waiting for the replacement board I unp luged the condenser fan which is a DC motor and uses the Board power. In place of that fan I use a small table top fan to keep the condenser cool. As it turned out I only needed it for 3 days because Parts Select did a super quick job of delivering the new board. Thanks for the super service!!!!!! Removal of the board only required unpluging the electrical connections squezing the retaining board pins with pliers and pulling the board out, pushing on the new board and connecting the electrical plugs. If the board locks like mine did, just unplug the main board power plug, let the memory clear and replug the power plug. The unit should then start and run with no problems.
Was this helpful?
Thank you for voting!
crisper drawer cover was cracked
9 of 12 people found this instruction helpful.
  • J.M. from Columbia, SC
  • Difficult
  • 1- 2 hours
  • Pliers
the part is a shell, it doesnt include the slider, gaskets, etc. these have to be ripped off the old cover -- usually by breaking the old casing. since the other parts were factory installed, they are damaged during removal and dont fit snugly, hence the need for glue. this issue should be clearly told to the consumer BEFORE ordering.
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people found this instruction helpful.
  • Gary from ROSETO, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Was this helpful?
Thank you for voting!
frezer door light switch broke (I have 2 boys :)
9 of 14 people found this instruction helpful.
  • inessa from manalapan, NJ
  • Really Easy
  • Less than 15 mins
The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!
Was this helpful?
Thank you for voting!
Water dispenser wouldn't work and refrigerator made an almost ghost like howling sound. Replacement main board fixed the noise. I purchased the replacement board for the ice and water (front of the refer) but haven't installed it yet.
7 of 8 people found this instruction helpful.
  • Brian from Woodland, CA
  • Easy
  • Less than 15 mins
  • Nutdriver
I watched the on live video. Piece of cake!
Was this helpful?
Thank you for voting!
no water in ice maker
7 of 8 people found this instruction helpful.
  • O.J. from SUFFOLK, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Change out water valve.. to find out my temp setting was to high. My kids changed the setting.. so my ice maker didnt work. The water valve will not open until it senses the right temp. Hope this help someone. But my part was here the next day
Was this helpful?
Thank you for voting!
refrigerator and freezer would not cool down.
6 of 6 people found this instruction helpful.
  • John from Lakeland, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
First, we called Sears Repair and had a technician come to our home. He stated the motherboard had gone bad probably due to a power surge (we had no surge protector on the appliance). His price for repair was $465.00. We opted to go online for the part and found it for $165.00 through PartSelect.com. It was a very simple procedure of remo ving the old and installing the new. A few turns with the nut driver to uncover the part, a few tugs with the pliers to disconnect and voila!.. The fridge was back to cooling in no time.
Was this helpful?
Thank you for voting!
no water to icemaker
6 of 7 people found this instruction helpful.
  • Ron from Clinton, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
turned off water supply, took screws out of bracket, then unhooked water lines. Installed water lines onto new valve, plugged it in then screwed bracket back onto fridge, turned on water and was back operating
Was this helpful?
Thank you for voting!
Freezer Light switch broke
8 of 13 people found this instruction helpful.
  • Kenneth from Milford, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!
Was this helpful?
Thank you for voting!
ice maker barely working
6 of 8 people found this instruction helpful.
  • William from Provencal, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Repair was very simple. Removed refridgerator bottom back panel, about 6 or 7 screws. disconnected bad valve, installed new valve , connected water supply line and then reinstalled panel. Took about 15 minutes from start to finish.
Was this helpful?
Thank you for voting!
Frame lower pan had cracked severely in several places
6 of 8 people found this instruction helpful.
  • Benjamin from Pittsburgh, PA
  • A Bit Difficult
  • Less than 15 mins
  • Pliers, Screw drivers
The only tough part was getting all the other parts off the old frame so that I could attach them to the new frame. In particular, the center rail required a lot of prying to remove, and I was concerned that it would break. Also, removing the sliders for the crisper drawer vents was a bit tricky; I ended up having to break the tabs that hold the vent covers in place, removing the vent covers, then removing the sliders.

Once I had reclaimed all the other parts, putting the new assembly together was pretty easy. My only concern is that the frame does not quite seat into the fridge in the correct way, it rides over the support knobs at the front.
Was this helpful?
Thank you for voting!
Refrigerator to warm
5 of 5 people found this instruction helpful.
  • Lloyd from PITTSBURG, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
Refrigerator and freezer would stop cooling. Would happen suddenly without warning. Reset of refrigerator would solve the problem and it would run fine for several days before doing it again.
5 of 5 people found this instruction helpful.
  • Jonathan from NEW ORLEANS, LA
  • Very Easy
  • 15 - 30 mins
  • Socket set
Only tool I used was 1/4 inch socket. Using the 1/4 inch socket, the screws were removed from the panel covering the control board. (this is on the back in the lower right corner). When this panel is off you are looking at the control board. Next remove all the plug in connectors. Don't worry about remembering where they go. They all are different and can only go in their specific place. After removing the connectors, pull the board out. Replace the plug in connectors before putting the new board back in , then snap the board back into place.(held in by four pins). Replace the cover.
Was this helpful?
Thank you for voting!
Unit had stopped making ice
5 of 5 people found this instruction helpful.
  • Ron from ORANGE, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.
Was this helpful?
Thank you for voting!
Ice Maker would not fill.
5 of 6 people found this instruction helpful.
  • Charles from Keller, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.
Was this helpful?
Thank you for voting!
All Instructions for the SDL20KCSBBS
61 - 75 of 542