SBK26DA Amana Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Left rear burner would not ignite
5 of 7 people
found this instruction helpful.
-
John from Perth Amboy, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours.
... Read more
John, N.J.
Read less
Was this helpful?
Thank you for voting!
Right front gas burner ignitor wouldn't spark
5 of 8 people
found this instruction helpful.
-
Joseph from Lake George, CO
- Easy
- 15 - 30 mins
-
Screw drivers
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one.
... Read more
Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Read less
Was this helpful?
Thank you for voting!
two burner ignitors would not function on cook stove
5 of 8 people
found this instruction helpful.
-
Warren from Las Cruces, NM
- Really Easy
- Less than 15 mins
-
Screw drivers
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Was this helpful?
Thank you for voting!
Load noise from dryer
4 of 5 people
found this instruction helpful.
-
Mike from Pacifica, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts
... Read more
on the pulley while the other adjusts the belt while putting the drum back into place.
Read less
Was this helpful?
Thank you for voting!
Bake element had failed
3 of 3 people
found this instruction helpful.
-
Elliotte from SNOW HILL, NC
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Inspect new part; collect tools; TURN OFF BREAKER; remove two screws holding defective element (KEEP!); install new element using saved screws; turn power back on; test; celebrate!
Was this helpful?
Thank you for voting!
Replaced baking element
3 of 3 people
found this instruction helpful.
-
Chris from Owatonna, MN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First, I removed the 2 screws holding the element in place. Next, I pulled the element out abotu 4 inches and disconnected the wires attached to the element. I was able to do one by hand, but the other required needle nosed pliers. (be careful not to pinch the connecting wire). Then I attached the wires to the new element. Lastly, I
... Read more
replaced the 2 screws to hold the new element in place.
Read less
Was this helpful?
Thank you for voting!
the bake element was burned into.
3 of 3 people
found this instruction helpful.
-
Jerry from Big Stone Gap, VA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
1. remove 2 screws holding element in place
2. unscrew the wires from the old element
3. the connectors on the new element was different from the old one
4. cut old connectors from wires
5. prepare wires for new connectors
6. install new connectors
7. connect the new element to the wires
8. replace the 2 ... Read more screws removed in step 1
9. test the repair
10 it worked great.
2. unscrew the wires from the old element
3. the connectors on the new element was different from the old one
4. cut old connectors from wires
5. prepare wires for new connectors
6. install new connectors
7. connect the new element to the wires
8. replace the 2 ... Read more screws removed in step 1
9. test the repair
10 it worked great.
Read less
Was this helpful?
Thank you for voting!
heating elements burned out
3 of 3 people
found this instruction helpful.
-
Billy from Corpus Chrsiti, TX
- Really Easy
- 1- 2 hours
-
Screw drivers
it was really easy. The most time consuming is removing an replacing the unit from the built-in cabinet.
Was this helpful?
Thank you for voting!
The old heating element broke in two!
3 of 3 people
found this instruction helpful.
-
Pamela from Gatlinburg, TN
- Easy
- Less than 15 mins
-
Screw drivers
First I turned off the circuit breaker...just to be safe. I removed the two screws that hold the element in place. I was surprised you didn't went new screws, but that was OK. I pulled out the old one, and pulled out the two wires. It was tricky, for me, to pull apart the old wires. Luckily, a friend was braver than I, and just pulle
... Read more
d them apart using a little muscle, and easily connected the new wires. I screwed it back in, and it was done! I was really impressed with how quickly it arrived at my door, too.
Read less
Was this helpful?
Thank you for voting!
burner needed replaced
3 of 3 people
found this instruction helpful.
-
michael from CHARLOTTE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers
removed old burner. 2 screws. disconnected connectors and reconnected new burner screwed back in place. turned on stove worked first time. perfect fit. 15 minutes total repair time. item arrived promptly and at half the price of the Whirlpool website.
Was this helpful?
Thank you for voting!
Baking element burned out
3 of 4 people
found this instruction helpful.
-
Lana from Colorado City, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Took two screws out of burned out unit. Pulled element forward and pulled off connectors. Replaced new element on connectors and screwed back in. Extremely simple. Less than 10 minutes.
Was this helpful?
Thank you for voting!
The dryer made a random grinding/rubbing noise during operation.
4 of 7 people
found this instruction helpful.
-
Timothy from Hardeeville, SC
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Wrench (Adjustable)
After removing the lower access panel, I observed the drum and belt and saw it turning freely. The support rollers in the back turned freely and were in good condition as well. At odd intervals the unit made a humming or grinding noise, and i decided to check the blower wheel (the other rotating part in the system). I found that the ce
... Read more
ntral hub of the wheel (which is made of a nylon like plastic) had sheared off from the wheel itself. I ordered a new part and started to remove the old wheel. **NOTE** many of the stories I read described how this part would have a reverse thread, it did not and that cost me an extra 30 minutes to figure out (the new part had arrows showing the correct direction to put on and remove - the original didn't). Once everything was cleaned and reassembled, I started the dryer again, but got no heat. I had previously replaced the heating element, so I thought my wiring was wrong. That wasn't the problem, but a hint from this site about checking the incoming wiring was the solution, my ground wire had come off the terminal in the back of the dryer and I wasn't getting the volatge across the element that it required. With the ground wire back in place, everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Noisy and blower wheel spin without turn motor shaft
2 of 2 people
found this instruction helpful.
-
William from FORT WAYNE, IN
- A Bit Difficult
- 30 - 60 mins
-
Wrench (Adjustable)
Removed lower panel, door assembly, belt and drum.
Removed blower wheel cover.
Used dremmel tool to cut plastic from metal that attaches the blower to the motor shaft.
Used adjustable wrench to keep motor shaft from turning.
Used vise grip to clamp on metal and turned to loosen blower wheel.
Attached new blower an ... Read more d re-assembled.
Removed blower wheel cover.
Used dremmel tool to cut plastic from metal that attaches the blower to the motor shaft.
Used adjustable wrench to keep motor shaft from turning.
Used vise grip to clamp on metal and turned to loosen blower wheel.
Attached new blower an ... Read more d re-assembled.
Read less
Was this helpful?
Thank you for voting!
noise in dryer
2 of 2 people
found this instruction helpful.
-
JOHN from MODENA, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
took frount off ,then filter, pulled drum out, then blower plate & spun impeller off. went back together easy ,except belt . that gave me a little problem but finally got it thanks
Was this helpful?
Thank you for voting!
The original unit burned through and would not work, of course .
2 of 2 people
found this instruction helpful.
-
Wesley from Guymon, OK
- Easy
- Less than 15 mins
-
Screw drivers
After unpacking and checking the unit that was mailed to me, I cleaned the ends of both the connections in the oven and the connections on the part, then plugged them together and screwed the plates in place in the oven. The oven worked immediately and still is working very efficiently. I had no problems at all with the installation.
Was this helpful?
Thank you for voting!