- Home
- RTG216NLD1
- Instructions
RTG216NLD1 Frigidaire Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer too cold
3 of 3 people
found this instruction helpful.
-
Curt from Maple Grove, MN
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.
Great resource and service, thank you.
Great resource and service, thank you.
Was this helpful?
Thank you for voting!
defrost heater not working; defrost timer not rotating so coils ice up
3 of 3 people
found this instruction helpful.
-
James from VOLANT, PA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.
Was this helpful?
Thank you for voting!
gasket was deformed; water condensed inside
4 of 7 people
found this instruction helpful.
-
Thomas from Pittsburgh, PA
- Easy
- 15 - 30 mins
-
Screw drivers
a handyman made the repair. It went fine.
Was this helpful?
Thank you for voting!
Water Was Leaking out of Refrigerator
3 of 4 people
found this instruction helpful.
-
Julie from Douglaston, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Our old gasket was shot to hell, so we figured we'd replace it to see if that would solve the problem. We followed the instructions of another customer. We realized it was better if we removed the entire door in order to attach the gasket. That took a little doing, but it was totally the way to go. Miracle of Miracles, the leaking has s
... Read more
topped, the food is super cold, and I couldn't be happier.
Read less
Was this helpful?
Thank you for voting!
The refrigerator wasn't cold enough.
3 of 4 people
found this instruction helpful.
-
John from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.
Was this helpful?
Thank you for voting!
Freezer was freezing but refridgerator was warm. Checked fan and it was not turning.
2 of 2 people
found this instruction helpful.
-
Jerry from PHOENIX, AZ
- Really Easy
- 15 - 30 mins
-
Socket set
Unplug fridge. Removed 2 nuts to get the vent plate off and two more nuts to get the motor mount off. Removed fan blade and then the fan motor. I put the new motor in and put everything back as it was. It was very easy. I had items in the freezer, so I didn't turn the fridge off other than to replace the part. It took about 6 hours for t
... Read more
he fridge to reach optional temps because I didn't get to defrost and the fridge had to work it out on it's own. If you don't need the freezer then you should turn the refridgerator off for at least an hour and open the doors so the coils can defrost and any ice blockage between the freezer and fridge portion can melt away as well.
Read less
Was this helpful?
Thank you for voting!
The original fan motor began masking a noise and finally stoped working.
2 of 2 people
found this instruction helpful.
-
Justin from FRANKLIN, TN
- Easy
- 30 - 60 mins
-
Nutdriver
Followed video instruction and completed the replacement. I had to join the wires since the connector was a male plug to a make plug.
Was this helpful?
Thank you for voting!
Drain pan for refrigerator
3 of 6 people
found this instruction helpful.
-
Lynda from Rocky Point, NY
- Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Took old defrost pan off, put new one on. Had to bend new defrost pan a little for it to fit..
Was this helpful?
Thank you for voting!
Frost in freezer, fridge not cold
2 of 3 people
found this instruction helpful.
-
Bob from Pinole, CA
- A Bit Difficult
- 30 - 60 mins
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I nee
... Read more
ded a new defrost thermostat. Installed fairly easy and problem gone.
Read less
Was this helpful?
Thank you for voting!
the freezer would stick in defrost and not come out
2 of 3 people
found this instruction helpful.
-
carol from woodland, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this helpful?
Thank you for voting!
first fresh food too hot, then freezer too hot
2 of 3 people
found this instruction helpful.
-
Rita from Lake Luzerne, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done
... Read more
!!! Couldn't have been easier.
Read less
Was this helpful?
Thank you for voting!
Defrost timer was not working
2 of 4 people
found this instruction helpful.
-
Harold from Grants, NM
- Really Easy
- Less than 15 mins
-
Screw drivers
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this helpful?
Thank you for voting!
Replace the gasket around the freezer door ($122.00 NEW GASKET)
1 person
found this instruction helpful.
-
Mary from FORT MYERS, FL
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Moved the old gasket aside to gain access to retaining screws in top freezer door. The new seal in the container we received was twisted, so laid it flat and used a hair dryer (as you advised) to regain the proper shape. Did everything possible, to align the gasket. Opened the freezer door to remove the retaining screws, began to reinst
... Read more
all the new gasket. The top came down both sides well. Attempted to install screws across the bottom, the gasket was so twisted would not conform back into the retaining frame on the bottom of the door. Therefore, it fits poorly. No proper seal. Sincerely, Jesse & Mary(also, the bottom of the freezer door plastic form was very brittle, broke where the screws fit....so we had to make a piece formed like a strip to re-enforce the areas that 'cracked' off so as the screws could align the bottom areas.
Read less
Was this helpful?
Thank you for voting!
Defroster didn't work
1 of 2 people
found this instruction helpful.
-
George from Eatonville, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this helpful?
Thank you for voting!
No freezing or cold in either freezer or refridgerator - compressor did not run.
1 of 2 people
found this instruction helpful.
-
George from Sunnyvale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this helpful?
Thank you for voting!