RST378 Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not light
2 of 2 people
found this instruction helpful.
-
Daniel from NAPERVILLE, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed old ignightor and installed new one
Was this helpful?
Thank you for voting!
Broiler inoperative
2 of 3 people
found this instruction helpful.
-
Donald from East Syracuse, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire
... Read more
within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Read less
Was this helpful?
Thank you for voting!
ignintion spark was very weak, burners would not light
3 of 6 people
found this instruction helpful.
-
marv from Eugene, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws
Was this helpful?
Thank you for voting!
Missing oven rack
2 of 3 people
found this instruction helpful.
-
Denise from Pittsburgh, PA
- Really Easy
- Less than 15 mins
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Was this helpful?
Thank you for voting!
igniter on top right front burner was shorting out,it would click but not ignite burner
2 of 3 people
found this instruction helpful.
-
Shelly J from KAPLAN, LA
- Very Easy
- Less than 15 mins
-
Pliers
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this helpful?
Thank you for voting!
the iron gets red hot but not enough to open the gas valve.
2 of 4 people
found this instruction helpful.
-
Paul from SEWAREN, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that yo
... Read more
u unplug the appliance !!!!
Read less
Was this helpful?
Thank you for voting!
no ignition at burners
2 of 4 people
found this instruction helpful.
-
Carroll from Lynden, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.
Remove and replace module and reassemble stove.
Was this helpful?
Thank you for voting!
Gas cooktop burners would not light
2 of 4 people
found this instruction helpful.
-
Bruce from Lake Oswego, OR
- Easy
- 30 - 60 mins
-
Screw drivers
We lived with the problem by using a long-reach butane torch lighter for three years after an appliance repairman told us the problem would be very costly to repair. Finally, we found the likely suspect when we happened onto PartSelect's website- the spark ignition module. The cost was just over $81 plus shipping. We ordered on Wednesday,
... Read more
it arrived on Friday by FedEx, and I installed it on Saturday morning. All the parts were included, the instructions were clear and complete, and, best of all, our range now works as it should. We couldn't be happier. Thanks, PartSelect.
Read less
Was this helpful?
Thank you for voting!
NO Work.
1 person
found this instruction helpful.
-
Robert J. from WESTMINSTER, MD
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC
Was this helpful?
Thank you for voting!
stove gas burner would not light?
1 person
found this instruction helpful.
-
Robert from Hendersonville, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceram
... Read more
ic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.
Read less
Was this helpful?
Thank you for voting!
old igniter would not light stove
1 person
found this instruction helpful.
-
Carlos from EAST NEWARK, NJ
- Really Easy
- 30 - 60 mins
Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter
Was this helpful?
Thank you for voting!
old igniter ceased to function
1 of 2 people
found this instruction helpful.
-
James from La Crescenta, CA
- A Bit Difficult
- 30 - 60 mins
-
Socket set
Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.
Was this helpful?
Thank you for voting!
The ignoter in the broiler didn't work.
1 of 2 people
found this instruction helpful.
-
John from Carlsbad, CA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
I bought the part and replaced it.
Was this helpful?
Thank you for voting!
Broken hinge on oven door
4 of 11 people
found this instruction helpful.
-
Robert from Morgan Hill, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started
... Read more
by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Racks would fall off of the tracks when the broiler was used
1 of 2 people
found this instruction helpful.
-
Andrew from Neptune, NJ
- Very Difficult
- More than 2 hours
I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be
... Read more
heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.
Read less
Was this helpful?
Thank you for voting!