RST378 Range - Instructions

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Unplug and pull range away from wall.
Remove metal panel from back of range by using nutdriver to remove 4 screws.
Use phillips scewdriver to remove 2 screws holding old spark module.
Unplug 4 wires from spark module and note placement of wires for reinstall.
Install new module by reversing procedure.
Slide range back against wall and plug in.

Entire process took less than 30 minutes.

NOTE: Spark Module received from partselect.com did not match old part exactly. The screw holes on the new part did not line up with screw holes from old part. I reinstalled new part with just 1 screw. Was told by partselect customer service that the part I received had been substituted and would work fine. It does work but it did not fit correctly.

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.

Unscrewed the burners,lifted the top up,unplugged the burners.Took out the bad module,making sure of where the wires went and put them in the same spots on the new module,reconnected the burners lowered the top screwed the burners back in and the burners lit.

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

First I removed the knobs on the range, then the front cover and then removed the two screws that hold each burner in place. I removed the top and removed the Module and started replacing the burners and front ocver and knobs. The Module worked GREAT. Thanks for your fast service in getting me the parts.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.

removed two screws from each burner, removed ignitor wires from burners, pulled range top removed old module and inserted new reattaching wires for four burners, switch and power to new module. reset top, attached wires to burners and reinserted screws