RST378 Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The burner would not light but the ignitor lite up fine.
0 of 1 people
found this instruction helpful.
-
Tom from West Allis, WI
- Easy
- 15 - 30 mins
-
Screw drivers
I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.
Was this helpful?
Thank you for voting!
Oven would not ignite
0 of 2 people
found this instruction helpful.
-
Ronald from Dedham, MA
- Easy
- 15 - 30 mins
-
Screw drivers
First I turned off the gas supply to the oven and disconnected it. I then pull the oven out away from the wall. I then unplugged the power cord. I removed the oven door by lifting it off of it spring hinges. I then removed a lower plate that covers the burner element by pressing in a manner that it popped off. I then located the igni
... Read more
tor and removed 3 screws. All were easily removed. Carefully, I pulled the igniter out and removed the wires from the wires that supplied the current to the ignitor. Installation followed by working the steps above in reverse order.
Read less
Was this helpful?
Thank you for voting!
Oven ignitor stopped working
0 of 2 people
found this instruction helpful.
-
john from lancaster, CA
- Really Easy
- 15 - 30 mins
Took off oven door, took out racks and bottom plate, removed burner assembly disconnected wires, removed old ignitor put new one in holder, connected wires, put burner assembly back, checked if it worked and replaced racks ect..No tools needed.
Was this helpful?
Thank you for voting!
the oven would not light
0 of 2 people
found this instruction helpful.
-
Kathy from Arlington, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
unscrewed the bracket holding the igniter in place then we pulled the drawer on the bottom out and disconnected the Igniter - then we took the unit out of the bracket replaced it and then put the bracket back into place screwed it in and reconnected the igniter and now it burns hotter then it has since we moved into the house two years ag
... Read more
o.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.
Read less
Was this helpful?
Thank you for voting!
Wall Oven - Igniter burning out.
0 of 2 people
found this instruction helpful.
-
Rianna from West New York, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I researched the needed part (igniter)and purchased it on line. It arrived promoptly. I called a repair person who arrived and installed the new part. All is well.
Was this helpful?
Thank you for voting!
Oven gas flash, igniter not heating up enough
0 of 2 people
found this instruction helpful.
-
Nelson from Selden, NY
- Easy
- 15 - 30 mins
-
Screw drivers
Removed old igniter held by one bolt & nut, diconected two leads to igniter. Gas mainifold remained in place during repair. Replaced with new igniter, using old mounting bracket and wire ties. Total repair time 30min, oven repair service wanted to charge $80 just for diagnosis. Total cost of repair doing it myself was $50.
Was this helpful?
Thank you for voting!
hinge broken again
0 of 3 people
found this instruction helpful.
-
Russ from Milford, NE
- Really Easy
- Less than 15 mins
-
Screw drivers
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this helpful?
Thank you for voting!
Door gasket gotten hard
0 of 7 people
found this instruction helpful.
-
Richard from Pocomoke City, MD
- Really Easy
- 30 - 60 mins
-
Screw drivers
I took oven door apart and replaced old gasket with new one.
Was this helpful?
Thank you for voting!
Oven no longer came on
-
jeffry from Sussex, NJ
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All
... Read more
went very well, and oven now works like a charm
Read less
Was this helpful?
Thank you for voting!
Ignitor would not ignite the oven
-
Fletcher from Greenville, SC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher
Was this helpful?
Thank you for voting!
Burners would not light everytime they were used.
-
Blaise from Deer Park, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.
Was this helpful?
Thank you for voting!
Oven stopped working with functioning ignitor
-
Angela from Brewster, MA
- Easy
- 30 - 60 mins
-
Socket set, Wrench set
Turned off gas supply and power. Removed four wires by hand and with a needle-nose pliers after making simple schematic. Disconnected gas supply to valve and valve outlets to broiler and oven. Also loosened other end of gas supply (on regulator) to swing it out of the way. Tools used....open end wrenches. Removed two nuts on left sid
... Read more
e of valve holding valve to bracket. Tools used...1/4" socket set. Since the nuts holding the right hand bracket were difficuly to reach, I removed the bracket, allowing the valve to be removed. Tools used....1/4" socket set. I then removed the right hand bracked and mounted it on the new valve. I then installed the new valve in the reverse order. I then opened the gas supply and tested the inlet connection(s) for leakage with soapy water. Perfect seal. I turned on the power, set the clock, and tested the oven and broiler. Worked perfectly. The only thing that prevented this from being a really easy job was the location of the valve....in cramped location.
Read less
Was this helpful?
Thank you for voting!
Oven door hinge broken
-
Sherry from Mountain Ranch, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this helpful?
Thank you for voting!
Door wouldnt shut evenly.
-
David from Westlake, OH
- Difficult
- 1- 2 hours
-
Screw drivers
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this helpful?
Thank you for voting!
Screws Were Rust6Ed, Melted
-
VICTOR from MOUNT PROSPECT, IL
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems
Was this helpful?
Thank you for voting!