MWX4 Washer - Instructions

I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, t ... Read more he machine ran as quiet as it did when I first bought it.

This was not exactly the right part for my machine, well, it was the right part, it was just a different design ro something. It didn't quite sit in the same place as the original, and so, the little hose is crimped a little, which makes the washer really loud. It's ok because it works now without babysitting. It was not difficult to inst ... Read more all, just took off the top panel with the star drive bit thingy, and took the old part off, installed the new part (forced it into place) and got it running.

After removing the rear cover I removed all the hose connections as this gives a better access to the mounting screws. Next disconnect the drive coupling. Remove the 2 inner mount screws frist then remove the 3rd screw.
Reversing this procedure makes mounting the new pump easy. Also I went to GE's web site and downloaded the parts ... Read more sheet that also gave me the number for the proper pump.
E. Renico

Remove front cover of stackable washer dryer to expose pump. Remove belt from drum and motor. Remove water lines from pump. Remove motor and pump which is on top of motor. Pump was rusted to shaft of motor which was removed by pry bars. Cleaned shaft with emery cloth and applied never siezed to shaft. Replaced motor. Replaced pump on shaf ... Read more t of motor. Replaced wiring. Replaced hoses. Replaced belt. Replaced hold down clips. Back in service.

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

took the top switch cover off. disconcected air line unscrewed switch assemble and replaced with new part and reconected air line. as good as new! it took longer to clean up the water then to fix the washer

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's ... Read more like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

I used a screwdriver to remove the front of the washing machine, fit the belt around the main pulley, held in the spring loaded tension pulley, and threaded the belt aound. It works great! I really need this inexpensive repair, since my job was downsized, and I can't afford to pay anyone.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

I was pleased with how quickly my part arrived and that it was still in stock as the washer was quite old. I had to remove screws on back panel to get at part. only a couple of screws held the part in place and 4 wires were connected. The hardest part was pulling the part out of black hose that connected water into machine. It had be ... Read more en on so long it wouldn't pull out and part of it broke off in hose. It took some fussing to get it out and then the new part connected easily.I took one wire off at a time and put on new part as to not get them mixed up.

After pulling $4.50 out of one of the hoses. I found that the fins inside the pump were gone. LOL I purchased another pump from partselect.com and proceded to install it. It was a simple installation, the hardest part was getting the hose clamp off of one of the hoses( it was one of those dang clamps you need a pair of pliers to remove). ... Read more I switched the mounting brackets from one pump to the new one and reinstalled the pump. Machine was running in under 1/2 hour. Thank you partselect.com

I unhooked the fill lines from the washer. I unscrewed the cover plate of the water inlet valve, and pulled the valve out enough to disconnect the fill hose. I unscrewed the band clamp on the fill hose and disconnected the hose.

I took the replacement part and one by one moved the four wires from the old part to the new part t ... Read more o make sure I connected each to the proper terminal. I then reattached the fill hose and clamped it. (This was the only "hard" part since the hose has little length to work with and is inside the machine.)

After attaching the all the internal connections. I took the coverplate from the old valve and screwed it to the new valve. I screwed it all back in place. Before reconnecting the fill lines from the wall, I replaced the rubber washers in the hose (a good practice to do when re-connecting these hoses). Connected the fill lines, and voila--working washer!

Very easy and intuitive repair.

Tilted the washing machine, removed 4 hoses from the pump and the drive connector;
removed 3 nuts that hold the pump; install
the new pump and put back the hoses; to be safe, I unplugged the electric

First I did some research and concluded the water inlet needed replacing. Obviously once you know what you need you go to PartSelet.com for parts and installation info. I went through the front of the machine. So I removed the front of the washer(2 screws at the front bottom)slide down the panel to separate it, lifted the top cover of the ... Read more washer(2 screws on the underside of the lid and 3 wire connectors to the fill switches) and then loosened the right side panel(3 screws at the bottom). Now pushing the wash barrel to the side it gave me enough room to squeeze my arms in to the inlet part. Be careful there are sharp edges and screw tips inside the machine. I removed the 2 wire connectors(hot and cold solenoids) inside the washer and then removed the screw from the back outside that holds the water inlet to the machine. Now I was able to pull the inlet closer to me so I could get pliers on the hose clamp to loosen and remove the old part. The new part was an improved version that was more solid. I attached the hose affixed the squeeze hose clamp and pushed the water inlet into place. The screws were not threading so I grabbed a couple of self taping hex head screws and a nut driver head for my drill and screwed the inlet in from the back of the washer. Then I replaced the wire connectors to the water inlet. With the water inlet complete, I reattached the right side panel, the washer lid, fill switch connectors and the front panel. Washer fixed and running perfectly!

I removed the four hoses that were connected to it, then I removed the three screws holding the pump in place. Then I removed the drive adapter that was connecting the pump to the motor. I then did everything in reverse order to install the new pump and everything worked just fine. Thanks!