MWX2 Washer - Instructions

first removed the 2 screws disconected the terminals, installed new switch connected wires back and test washer and it worked like new, i put a Jumper to get the washer to work while i got the parts. Also i received the parts in 24 hrs. Thank You.

took motor lose and belt lose first, then took pulley off from the tub shaft, then made a big mistake, I took and pulled the lower shaft seal. lucky I had a pan to catch the oil about half a gallon. After that I could not find away to put oil in the gear box, so I took the drum out and that didn't work but it was a good thing I did becaus ... Read more e the inside drum was rusting so I spend money on the seal for nothing. Had to buy a new washer. If I ever did it again I would turn the whole washer up side down so the oil could not run out and I would put the oil in the hole where the seal was. lot of work for nothing.

Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a ... Read more repair manual so every step was trial and error untill I was able to complete the repair.

loosen the clamp holding the flex coupling then remove the 3 screws holding pump in place remove old pump and coupling best to have washer laying on it's face for easy access to screws.
install coupling on new pump and install togeather then attach flex coupling to drive motor...

First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, ... Read more put the hoses on, plug in motor and replace front panel. plug into wall

After turning the water off and removing the hoses,I pulled the top off by removing the 2 screws from the clips in the back and popping the 2 spring clips in the front. I then removed the 2 side screws left and right to allow room for the sides to move out of the way of the motor. The back panel is spot welded so the panels stayed connect ... Read more ed. I then removed the 2 screws from the water overflow guard on the motor. Once removed I unplugged the wire harness from the motor. After that the 4 nuts were taken off of the bottom of the motor. I pushed the belt tensioner in and pulled the motor out. Install the motor making sure the nuts are tight as they can work loose from vibration.

Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.

I pulled out machine turned off the water ,and unpluged the machine. Took off the hot and cold water hoses with help of vise grips. Next the two nuts which hold's the part to the machine(plate) and the nut that holds the part to the plate pulled out the part marked the four wires which go onto the part undid clamp on hose and pulled off ... Read more hose. put the hose on new part , re-attached the wires , put part on plate and attached plate and part to machine hooked up hoses turned on water and plugged in machine . The washer does not leak and works great. I'm a 59 year old woman.

Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have cl ... Read more ean clothes.

First I took sides off the washer. I then took screws out of the Drain pump holder. Unclamped the two pipes from it. Undid the wires to then drain pump. Screw in the new pump hardware. Plugged in the wires on side of the pump. Reclamped the pipes. Put sides back on washer and it worked. That easy and took less then 30 minutes. I am no ha ... Read more ndy man so thats how easty it was.

I got online and figured out exactly how to take off the front of the washer and then how to replace the belt. It was so easy. The part itself arrived much sooner than predicted. It fit perfectly and my washing machine is now running smoothly and quietly.

My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the ... Read more safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money.

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, di ... Read more sconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 ... Read more screws and reconnected the 4 wires.

To replace the pump remove to lower screws on the front panel,remove panel ,pump is in the front section , remove two screws that attach pump to lower housing.
To replace timer remove screws on the plate that the contrlos on mounted on. Once you have access to timer you must remove the nylon pin in the back of the timer that holds th ... Read more e dial to the timer base.You can not remove the knob without removing the pin