MW10 - Instructions

The unbelievable happened. Our glass carousel cooking tray developed a crack. Each day the crack got longer. I ordered a new one on Tuesday and it arrived the next morning just before the cracked one completely cracked. I have never experienced such fast service. I highly recommend PartSelect and their helpful service.

replaced the plate

Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received i ... Read more t two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.

I ordered the part and when I recieved it, I saw that I had orderd the wrong size. I called and customer service was very friendly and helped me to get the correct part. they sent the new part out and even though it was christmas hollidays I recieved it the day after Christmas. Great Company

I went on line and tped in GE your web site came up. It didn't even take 5 minutes to order the part. The best part was I ordered it on Sunday and when I got home from work that Tuesday it was at my front door. I will certainly use your company again.
Thank You

Opened the box and put the new tray in the micro wave. Drank a beer and made microwave popcorn. The End!

i had to replace the cooking tray after 9 yrs as i dropped it and broke it. i ordered the new tray in feb and rec'd it right away. the new tray mysteriously burst one day in the microwave after a few weeks. i spoke w someone at partselect and they replaced it right away. wonderful customer service. thank you.

put cooking tray in place

We were so happy to be able to order a replacement glass microwave tray after I broke ours during cleaning. In this throw-away world we live in, we assumed we would just have to buy a new microwave but ours was only two years old so we really didn't want to do that. We found the same microwave at the store but it had gone up in price qu ... Read more ite a bit. Ordering this plate as a replacement part just made financial sense, and it was so easy to order. It arrived very quickly and we were extremely pleased with the whole experience.

My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off a ... Read more nd putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!

First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was ... Read more a little hard to installed but, I used a hammer and tapped it in. Third, I also put some lubricant on the new coupling to help the agitator slide down a little easier on the new coupling.

P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)

## WHAT I WISH I'D KNOWN BEFORE I STARTED ##
1. Remove the four hoses first.
2. remove the three screws holding the pump to the structure above BEFORE loosening the flex clamp.
3. with the pump free of the hoses and rest of the washer, then remove the flex coupling clamp from the pump end only; do not remove the flex coupli ... Read more ng from the motor.
4. remove the old pump.
5. attach the new pump to the top of the flex coupling BEFORE attaching the pump to the upper part of the washer. This is the most difficult step, to get the flex coupling on the pump in a secure fashion using the clamp. It's much easier to do if the pump is not yet connected to the rest of the washer.
6. attach the pump to the washer with the three mounting screws.
7. re-attach the hoses.
8. run the washer and check for leaks.

I made the mistake of taking the flex coupling off the motor then tried to put the flex coupling on the motor and the pump when the pump was already attached to the washer. Major grief :>(

Good luck, it's well worth the effort.

1. removed vent across the top to gain excess to Screw holding control in place. 2. Removed control panel to access Fuse. 3. Remover fuse after pulling plug. 4.Tested fuse for continuity with volt ohm meter noting no continuity.5. Orderd new fuse. 6. receeived new fuse and installed infuse holder.7. plugged microwave plug back in receptic ... Read more al and tested unit now working OK.Reversed steps 2 & 1 job complete

I looked up the #1 reason for no heat for my microwave on the site , and using my model number found that 92% of the time it was the Black Sleeve Diode. Ordered the $15 part, and installed it within 30 minutes. Most of the time was used for removing the built in microwave and removing the cover. Replaced the diode by finding it on the ... Read more diagram that I printed from this site (free). Very relieved that we don't need to have our custom cabinetry re-sized to accommodate a new microwave. Thank you!

put washer on its side,removed 1cross section,loosened the nut that held on the pulley.
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose, ... Read more set washer to spinanr turned it on to make sure no more leaks.
everything is working well