MRS26 - Instructions

Partselect made it easy and affordable to replace the part myself. It arrived on the 3rd day after ordering. Thanks

Noticed no cool air was coming from the vent on the refrigerator side. After cleaning out the freezer side, I noticed that the air intake at the bottom of the freezer was frosted over.I removed the metal panel and discovered the coils were completely frosted over so I found the defrost timer located at the bottom left corner of the refrig ... Read more erator. took a screwdriver and turned it very slowly to force a defrost. i watched the coils for awhile and noticed that the heat element would never deice. so I thought it may be the thermostat clamped to the top of the coil might be bad. I unplugged the thermostat and plugged the heat element coil directly to wires feeding to the thermostat. On my refrigerator the wire connectors will allow to bypass thermostat. After waiting twenty minutes, I forced another defrost cycle with the timer and noticed the heat element would still not defrost. So i unplugged the heat element and took a test meter and checked the wire connectors and found one twenty volt at the connectors. So, therefore, I determined it must be the heat element itself. Even though they rarely give trouble. I found the service diagram on the back of the refrigerator in a plastic pouch, and it said the ohm resistance should be twenty two. My element read 145 so that also pointed to a bad heat element. I took the screw out that holds the coil in, lifted it about two inches, and pulled the bottom of the coil out just enough to remove the heat element from the coil and discovered it had a crack in it. It must have been a Monday at the factory, because the heat element looked like it had been warped while being installed.I ordered a replacement element and installed it. I works as good as new. I do electrical work for a living, so this was pretty easy for me to figure out.

I purchased the replacement part (no instructions sheet) from another company, not this one, that cost 2X's a much as this company. So I sent it back and ordered from this company. Got it faster then the post office sends us the stamps we order by internet and this ice maker had instructions.
Our's is a side by side refrig, so workin ... Read more g space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray.
I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.

Bought a new
capacitor.

Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation

I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job.
I found this part easily on the web site $77. ... Read more It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.

Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be st ... Read more uffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.

Since we will be working with water and do have an electrical connection nearby, it will be best to unplug the refrigerator to do this repair. It should only take about 15-20 minutes to complete the repair so your contents in the refrigerator should be fine.

1-SImply pull your referigerator away from the wall and unplug it. ... Read more r />
2-Locate water supply valve and turn off water to refrigerator by closing the water valve.

3-Remove two 1/4" screws that hold the black "cardboard" cover at the bottom right corner of refrigerator.

4-Then locate the two 1/4" screws holding a light blue valve assembly, again in the bottom right corner of refrigerator. Remove screws and assembly will be loose.

5- Remove water line from the top of the valve assembly you just loosened.

6-Then unscrew the large plastic nut on bottom of valve assembly.

7-Unplug the electrical connector that is on the top of the valve assembly.

8-Install the new valve by reversing the installation. Plug in electrical connector, tighten water line on bottom of assembly, re-attach/tighten main water line on top of assembly- and re-attach valve assembly to refrigerator and re-install cardboard cover. Turn on water supply to refrigerator and check for leaks. Don't forget to plug the refrigerator back in.

Thats it! Problem solved!

Read less