MRS1 Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The supports for the crisper cover had broken and the draws would not open correctly
2 of 4 people
found this instruction helpful.
-
WAYNE from NOVATO, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.
Was this helpful?
Thank you for voting!
Defrost timer was not working
2 of 4 people
found this instruction helpful.
-
Harold from Grants, NM
- Really Easy
- Less than 15 mins
-
Screw drivers
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this helpful?
Thank you for voting!
Right side door was grinding on the spindal.
1 person
found this instruction helpful.
-
Donna from Palmdale, CA
- Really Easy
- Less than 15 mins
-
Wrench set
We took the door off and replaced the pastic washer. Found out that the repair people never informed us that the door itself has a bit damaged so this repair would have to be done over and over. Nice way for them to make money off us.
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yours ... Read more elf!
We were able to fix it so that it will last a LONG time. Sometimes it realy can pay to do-it-yours ... Read more elf!
Read less
Was this helpful?
Thank you for voting!
Temperature in both freezer and fridge sections to warm!
2 of 4 people
found this instruction helpful.
-
Thomas from Spokane, WA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 pa ... Read more rt if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 pa ... Read more rt if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
[email protected]
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Freezer door caps
1 person
found this instruction helpful.
-
Lisa from LAS VEGAS, NV
- Really Easy
- 30 - 60 mins
They were the wrong parts. I read a question another person asked and it advised to order these parts. Didn't want to waste my time anymore and threw them away.
Was this helpful?
Thank you for voting!
Defroster didn't work
1 of 2 people
found this instruction helpful.
-
George from Eatonville, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this helpful?
Thank you for voting!
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
2 of 5 people
found this instruction helpful.
-
Larry from Newton, KS
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this helpful?
Thank you for voting!
Refrigerator keeps frosting up and not cooling
1 of 2 people
found this instruction helpful.
-
Marvin from Pima, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, goi
... Read more
ng to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.
Read less
Was this helpful?
Thank you for voting!
No freezing or cold in either freezer or refridgerator - compressor did not run.
1 of 2 people
found this instruction helpful.
-
George from Sunnyvale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this helpful?
Thank you for voting!
Coils kept icing and refrigerator stopped cooling lower compartment.
5 of 14 people
found this instruction helpful.
-
Raymond from Sierra Madre, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Replaced defrost timer & thermostat.
Other Parts Used:
Was this helpful?
Thank you for voting!
door shelf ends broken off from constant pulling on door and slaming it with 2 gallons of milk in door.
1 of 3 people
found this instruction helpful.
-
Katherine from Lafayette, LA
- Really Easy
- Less than 15 mins
Inserted the caps into the bar and snapped in door. That's it.
No tools needed! Hope it last another 20 years
No tools needed! Hope it last another 20 years
Was this helpful?
Thank you for voting!
door shelf end caps were broken
1 of 3 people
found this instruction helpful.
-
Lupe from Las Cruces, NM
- Really Easy
- Less than 15 mins
-
Screw drivers
removed broken end caps, took a small screwdriver and simply applied a little pressure to release them. Pushed new end caps into place (they just snap in). Presto done!!
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people
found this instruction helpful.
-
Denise from Landover, MD
- Really Easy
- Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
broken lips on the drawer
1 of 3 people
found this instruction helpful.
-
albert from nashwauk, MN
- Really Easy
- Less than 15 mins
removed drawer, removed front, slid in the front, put back in. done
Was this helpful?
Thank you for voting!
sheft ends brolen
0 of 1 people
found this instruction helpful.
-
Helen from Gulf Breeze, FL
- Really Easy
- Less than 15 mins
Cleaned and removed old ends, applied new ends and installed. Ends fit to order, shipping quick and parts affordable. Thank you
Was this helpful?
Thank you for voting!