EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

MRMR General Electric Range - Instructions

All Instructions for the MRMR
106 - 120 of 145

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Trim part on bottom of door was rusty
  • Richard from Euclid, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver
I ordered the part, It came a few days later,,Within 15-20 minutes, I had it installed..Pretty easy...Thanks
Was this helpful?
Thank you for voting!
A large burner (haliant Burner 8" ) went out on my Hotpoint Electric Range
  • Ruth from Potosi, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!
Was this helpful?
Thank you for voting!
Handle on oven door end cap cracked
  • Garry from SAN ANTONIO, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The repair was easy except what caused it to break .Their was a missing screw on the door itself that was never put on or came off could not find old screw,once it was replaced new part was stronger than before.
Was this helpful?
Thank you for voting!
Stove door handle broken
  • Melvette from Stamford, CT
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unscrewed the old broken pieces to the handle and put on the new handle, very easy!!!
Was this helpful?
Thank you for voting!
The original oven handle end caps were cracked
  • Chris from New Ulm, MN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I disassembled parts and panels from the oven door as needed to remove the handle end caps. It was not clear to me what the best disassembly method was, because I used a different method when assessing the problem as when I performed the actual part replacement. The quickest way is to take the top two screws on the inside oven panel loo se, but leave them in their retainers. Remove the side trim screws on the plastic upper side pieces. Remove the four sheet metal screws on the bottom of the door, located the far right and left (two on each side). Carefully split the inner and outer oven panels to access the mounting screws for the oven handle. Replace the oven handle and reverse the disassembly process.
Was this helpful?
Thank you for voting!
Replace damaged oven door handle
  • Byron from Fayetteville, GA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Required removing the door, by sliding it off the hinges (open 1/4 then lift up), removing the outer frame which releases the inner glass door section exposing the door end screws. Removed the phillips head screw on each door end releasing the old handle. Inserted the new handle in the ends, screws replaced, reversing the above. Thank s for the correct part. Byron C.
Was this helpful?
Thank you for voting!
Rusted oven door trim
  • Todd from Pittsburgh, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver
Removed old part by removing the screws at the boottom of the oven door. I wasn't sure if the glass oven door cover would remain in place once the trim piece was removed, fortunately I was ready when it came down. The glass cover is large and heavy so you need to be ready to handle the bulk of this piece once the last screw is removed. Cleaned everything and with the help of my wife, who secured the oven door cover in place, secured the new trim piece by replacing the screws. What a difference, looks like new! PartSelect provided great service in terms of speed and part acciracy.
Was this helpful?
Thank you for voting!
End cap plastic broke at screw entry
  • Alan from Mars, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Removed door from oven. Removed all side screws and pulled front assembly from door. Discarded old screws and broken plastic pieces. Put old handle in new end caps and lined them up with screw entry holes. It took 2 people to hold the door up while pressing in the screws to enter the new plastic receivers on the end caps. A pretty eas y fix.
Was this helpful?
Thank you for voting!
Broken door handle
  • John from Milan, TN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.
Was this helpful?
Thank you for voting!
The range kept giving an F2 alarm
  • Les from Coal Creek, CO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Was this helpful?
Thank you for voting!
broke end cap while moving range
  • Alan from Muskego, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this helpful?
Thank you for voting!
Right Oven Door Handle End Cap Broke Off
  • James from Fort Myers, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Socket set
Went on line and watched a couple of instr. videos which were very well done and explained just how to replace the end cap. I purchased and relaced both end caps and was able to clean the entire handle before putting it all together. Looks really good now. Thankyou. JJM
Was this helpful?
Thank you for voting!
Door handle end cap got brittle and broke on oven door.
  • James from Wiscasset, ME
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Slide oven door off slides and put oven door on table. Removed 2 torx-20 screws from top of oven door on the inside. Remove 4 sheet medal screws from the bottom of door 1/4' socket heads. The inside of the door will now separate from the front of door.Now you can see 2 screws on each side of the door handle end caps on 1/4 " socket heads. Remove the 2 screws on which ever side is broken and remove old end cap and side new one on an install 2 screw. When you put door back together there are 2 spring steel spacers that fall off the top 2 screws that hold the inside and outside at the proper space! Parts Select service is EXCELLENT!!!!!
Was this helpful?
Thank you for voting!
handle on door broke when trying to remove front oven glass for cleaning
  • GEORGE from CYPRESS, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench set
Replaced two end caps attached to door handle and two plastic side covers.
Was this helpful?
Thank you for voting!
Bad Burner
  • Roosevelt from Waggaman, LA
  • Really Easy
  • 15 - 30 mins
I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.
Was this helpful?
Thank you for voting!
All Instructions for the MRMR
106 - 120 of 145