EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

MRMR General Electric Range - Instructions

All Instructions for the MRMR
91 - 105 of 145

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broke ed cap on oven door
0 of 1 people found this instruction helpful.
  • HAROLD from LODI, CA
  • Very Difficult
  • 1- 2 hours
  • Screw drivers
Repair was basically simple. Remove 6 screws holding door facing on door, remove one screw holding handle end caps in place. Then reverse the operation installing handle end caps. The problem I had was that the new a end caps had different dimensions than the old ones and the handle wouldn't slip into them. Had to carve away material inside the new caps with an exacto knife in order to fit the handle. The result was a 15 minute job took well over an hour
Was this helpful?
Thank you for voting!
Door Handle End Cap Broke Off
0 of 1 people found this instruction helpful.
  • Lori from Fairfax, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Wrench (Adjustable)
Dislodged screws to oven door to get to handle assembly. Fairly easy, however, new door handle end caps do not come with screws and the old screws were not a good fit. Almost stripped the old screw trying to get it in place. Strongly suggest that Part Select send replacement screws with handle to facilitate repair. Door handle is back up but is now loose until I can find/secure appropriate replacement screws and repeat the process all over again.
Was this helpful?
Thank you for voting!
A end bracket for the oven door handle was loose. The internal socket (anchor) holding the screww that joints the bracket to the oven door snapped.screw
2 of 8 people found this instruction helpful.
  • Dominick from housatonic, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Socket set
Remove the front panel, at which time the spring loaded door slammed closed while the paned and handle were in my hand. Fortunately I had a star bit to fit the screw holding the door and panel together.The parts should come with 2 screws since the part has holes for 2. note: the factory installed handle only had 1 screw in each side.
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people found this instruction helpful.
  • Roscoe G from ROCHESTER, NY
  • Very Easy
  • Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Left bracket broken on range oven door handle.
  • Roger from De Soto, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Using a torx screwdriver, I removed the old handle bracket. I had to be careful not to lose a metal spacer that went between the back of the door front panel and the back of the inside door panel. With the door in full open position, I was able to hold this spacer in my thumb and fore finger while I removed the screw. The broken portio n of the handle bracket fell to the floor. With the old handle removed, I placed the screw through a hole in the inside panel, through the spacer and through a hole in the front panel. While holding the front pull bar in the right handle bracket, I placed the new bracket on the bar holding it in position on the door and attaching the screw. Easy peasy!
Was this helpful?
Thank you for voting!
uneven heating of oven
  • John from Sandstone, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this helpful?
Thank you for voting!
Oven Door Handle End Caps.
  • Linda from Lake Panasoffkee, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I purchased my stove second hand. It was a mess but I saw a gem under all that dirt and grime. It took me a week and it looked brand new. The end caps on the oven door handle were discolored and cracked. They made the stove look old. It was an easy repair and my stove looks brand new. I will order an extra set just in case as these pa rts are getting harder and harder to find. I am so pleased with the original parts. They were here with in days and well before promised delivery date.
Was this helpful?
Thank you for voting!
Plastic end caps for oven door handle brokr off
  • Ben from The Hills, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
When the replacement parts came (only took 2 days). I lifted the door off. Removed the screws that held the tempered glass front on the rest of the door. Removed the screws holding the broken end caps Replaced one end cap, inserted the handle, and fitted the 2nd end cap to the handle and screwed it in place. Screwed the front of the door to the back and replaced the door on its hinges. Easy as pie, ....Easier!
Was this helpful?
Thank you for voting!
Oven Door Handle Broke
  • Heidi from Carrollton, TX
  • Really Easy
  • Less than 15 mins
The repair was very easy. It did require a very small torx driver (I can't remember the size off hand.) and a 1/4" nut driver.
Was this helpful?
Thank you for voting!
8 inch burner was burnt out
  • Luis from Kissimmee, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burn er connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.
Was this helpful?
Thank you for voting!
Trim has tendancy to rust on range oven door
  • Carole from San Diego, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed bottom screws, replaced trim. No trouble.
Was this helpful?
Thank you for voting!
replace end caps
  • Thomas from Glen Island, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
The video was very helpful.Very easey repair
Was this helpful?
Thank you for voting!
End Cap broke on oven door.
  • Georgianna from Austin, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was easy as pie. Just followed the instructions.
Was this helpful?
Thank you for voting!
handles broken on oven door
  • Rita from Yadkinville, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
removed old handles and slid door apart align new handles and re-installed new handles. One person job.
Was this helpful?
Thank you for voting!
left end cap for oven door
  • Diane from Kingston, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
First, the order was shipped and delivered immediately. The model number had a wider range to select from and I had to guess which was the better fit. Other then that the new handle installation was a snap. Thank you and we would surely order from your company again.
Was this helpful?
Thank you for voting!
All Instructions for the MRMR
91 - 105 of 145