KUIS18P KitchenAid Ice Maker - Instructions

My husband took the old motor out by taking the screws out. Then, he unplugged the fan. We searched your site for the part. With the pictures on the site, we were able to match the motor exactly. The delivery was really fast. When we received the part, he installed the fan and plugged in the power connector. We have replaced refrigerator ... Read more fans before but anyone can do this with no experience. Just follow the instructions and you're all set.

I replaced the bin ice sensor with the new one from partselect.

There was a loud noise coming from the fridge - we ordered the new part it came a lot sooner than we excepted and we replaced it in about 20 minutes- the hardest part was my husband getting his hand in there to put the screws in- but a very easy fix.

remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy ... Read more to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.

I called a repairman to come out and he said it would cost $320 dollars for the repair. So I bought the part and spent $85 dollars and about 25 minutes to repair it myself

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

removed the front cover below the compartment door,removed the 2 screws holding the valve to the case and removed the water lines from the valve.The process was reversed to install the new valve.

Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibil ... Read more ity. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice.

Removed back panel and removed the motor put new quick disconnect on and tapped the mounting holes. Removed and cleaned fan blade from old motor and put on the new motor. Mounted motor plugged it in and replaced panel.

Disconnected both water lines and two mounting screws. Installed new water lines and water valve. No problems at all. Ordered the valve on a Monday and received it the next day. Even though i chose FedEx ground. GREAT SERVICE! I am a technical service manager and I always give credit to company's with great service. In fact, I have sent y ... Read more our website link to our management team to show what our website could be for our customers. Easy to find part numbers, pictures of the part being ordered and ease of use. World Class support.
Kindest regards,
Dave

Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.

just replaced the water inlet valve, it took less than 10 minutes. Ordering the part was just as simple, no hassle what so ever. Got the part as promised and installed it in minutes just as it was explained. I will come back to this site in a hart-beat.

Thanks

r&r fan blade and motor. with the parts you supplied it was easy. the parts were perrrrfect. thank you very much. job well done. bruce

Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy wi ... Read more th parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company