KSB3 KitchenAid Blender - Instructions

The repair is easy. Just follow the directions that come with the replacement part. And parts select is awesome. I received the parts within a couple of days and fixed it right away.

I will definitely use this company again. The blender was over $120 when I brought it and I did not want to spend that kind of money again. My co ... Read more st to fix was about $8.00 for the part and $7.00 for shipping. Hmmmm, $15 vs. $120+ sounds like a good deal to me.
Thank you.

Went to several online blog sites. Repair of the Kitchenaid blender is a hot topic. Could not repair it the way the instructions indicated. One person used a hammer and that did the trick! Who would have thought to use a hammer?!

I first tried to do the repair just like the directions ,trying to force off the wheel. Then I tried doing it the way the readers here did with a tthin pliers and was not sucessfull. I then took it to a hardware store and ask about a certain pliers,they did not have it. The older man at the register took two screwdrivers from the jar next ... Read more to him took my blender and pried on either side and popped off the wheel just like the original directions said. It was then easy to put the new one on.

I used a straight edge screwdriver. At first my husband and I were afraid to much too much force behind the old coupling, but I figured it's no good the way it was so used more force and "pop" it came off. Then installed the new one and I love my blender!!

Replaced the timer

Being an aircraft mechanic for years I pride my self on being able to fix anything that my wife buys. So I tried to replace the drive gear for her kitchen aid blender without reading the instructions, much easier to read.
Thanks,

Following the instructions which was quite clear.

Simply to find the look of dismay in her face. After I violently began shaking and dismantling the compactor in disgust. I decided to unplug it from the wall, I then gathered my senses and began to perform a electrical diagnosis and found that the rotary swich contacts, which activates the compactor, had gone bad. I simply went to the w ... Read more ebsite and selected my part # from the detailed spec sheet. I chose to receive the package on a three day shipment. Here it arrived, installed the part and away the problem went. While on the parts list I included bag brackets that had broke over time and now my compactor is like new.

Last time this happened we simply used a thin wrench to unscrew the damaged coupling. This time it was so tight no wrench could undo it. We had to grind it off using a grinder drill until it was so loose it popped off.

I used a pair of diagonal cutters to nip away at the drive coupling which had become gummy and soft. This exposed the inner aluminum hub that the drive coupling was molded to. I used several pieces of masking tape to protect the blender finish under the drive coupling. The instruction supplied suggest to pry upward with a screw driver at ... Read more 1/4 turn intervals until it comes off the motor shaft. I thought this was a rough approach, as I was concerned about damaging the threaded motor shaft. Also note that the motor shaft has left handed threads, you would turn clockwise to loosen the drive coupling. The first approach I tried was to use a small ignition wrench, there are two flats directly below the coupling aluminum hub which measured 9/32" across the flats. The wrench even though small would have to been ground thinner to fit, this may have worked. I decided to use approach two. I used my dremel tool with a 1/32" cut off wheel and cut through each side of the aluminum hub staying away from the center where the motor shaft is threaded. Across the center of the hub I only cut through half the thickness, I then used the diagonal cutters to fold each half agains itself (the hub actually fell off). I installed the new coupling turning it counter clockwise on the motor shaft. I attached the blender jar filled with water with the jar lid on and toggled the blender on and off a few times to further tighten the drive coupling.

used needle nose pliers to hold shaft after prying rubber top off. unscrewed metal tap, counterclock wise. installed new piece

The part comes with instructions on how to replace the coupling. The instruction basically says to pry out the worn coupling. This is exactly what you should do. It might sound strange or brute force but it actually works. The coupling is actually made of some soft metal that comes out easily. The only downside is that you have to clean ... Read more up the leftover metal bits. You don't need to find a slim wrench for the motor spindle as suggested by other in the thread ..... just follow the instruction pry out the old coupling.

Hammer was used to remove the old one, tapping quickly on old coupling. I did use a thin pliers (wire stripper) to hold shaft when I screwed on new coupling, even though it said one did not need to. Good instruction sheet came with the new coupling.

I looked on the Web for help in changing this part they suggested prying the part off with a screwdriver. This would work but I figured this approach was a little to brutal.I had a set of distributor wrenches and these had one that fit the shaft under the drive coupling Using the wrench to hold the shaft I used a small set of water pump p ... Read more liers to remove the coupling.As the directions on the Web states this is a reverse thread.The whole project took all of five minutes to complete

I used a screwdriver,pulled out the piece,then change with a new one,that I was ordered before.It was ver easy to assembly.