EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JSS014J2 General Electric Range - Instructions

All Instructions for the JSS014J2
106 - 120 of 416

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Knob/switch would not turn right front burner on at all!
3 of 7 people found this instruction helpful.
  • William from West Liberty, KY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enoug h slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!
Was this helpful?
Thank you for voting!
Oven lower Bake Element exploded
1 person found this instruction helpful.
  • Fred from Renton, WA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire co nnection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.
Was this helpful?
Thank you for voting!
Bottom element had burnt out.
1 person found this instruction helpful.
  • Robert from Harrisburg, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplugged stove, removed front door, carefully removed two screws holding the cover plate of the element. Gently pulled the element out about 3-4 inches removed the two screw attaching the electrical wires to the element , making sure the wires did not pull back into the stove. Removed old element, attached new element to the electrical wires with the new screws received with the new element. Carefully pushed the wires and element back into place making sure the insulation was also in place. Re-attached the cover plate with the two screws I had removed. Plugged the stove back in and tested the element. Replaced the front door .... job complete!

Just wanted to add that the part came in two days, super mailing time, thanks!!
Was this helpful?
Thank you for voting!
The oven heating element was broken
1 person found this instruction helpful.
  • Daniel from Denver, CO
  • Really Easy
  • 15 - 30 mins
  • Pliers
I removed the 2 screws and the 2 wires from the broken heating element. I removed the broken oven heating element. Then I attached the 2 wires to the new heating element and put the 2 screws in to attach the new heating element into the oven. The new oven heating element worked just fine and I was done.
Was this helpful?
Thank you for voting!
Bake element developed a hot spot that burned through it.
1 person found this instruction helpful.
  • Paul from Slatington, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my fing er to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.
Was this helpful?
Thank you for voting!
boken element
1 person found this instruction helpful.
  • cynthia from snyder, NY
  • Really Easy
  • 15 - 30 mins
  • Wrench set
remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in
Was this helpful?
Thank you for voting!
Element at the bottom of oven cracked
1 person found this instruction helpful.
  • AMELDA from BRYANS ROAD, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers
First I turned off the circuit breaker leading to the oven. Then I removed the two screws that held the old element in place. I pulled out the element and disconnected the wires. I reconnected the wires to the new element and pushed it back in place. I then secured it with the two screws. I turned the circuit breaker back on and turn ed on the oven. Works just great!!!
Was this helpful?
Thank you for voting!
Element either shorted or burned out.
1 person found this instruction helpful.
  • Patrick from Durham, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
Removed two socket head screws form inside oven rear wall. Pulled element out and disconnected two screws attaching wiring. Replaced with new.
Was this helpful?
Thank you for voting!
All burners on stove needed to be replaced due to age
2 of 4 people found this instruction helpful.
  • ROY from CULPEPER, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed instruction that came in the new parts. Each element took about 10 minutes to remove, inspect the wires, clean the connections and reconnect the new elements. The element covers that came with the kit were easy to install, and everything fit just fine. Most important thing is to turn of the electrical power to the unit BEFORE you start.
Was this helpful?
Thank you for voting!
elememt not working
1 person found this instruction helpful.
  • ROBERT from ORWELL, VT
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 person found this instruction helpful.
  • NEIL from ROCKY POINT, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
Broiler and Baking elements replacement
1 person found this instruction helpful.
  • Joseph from Buford, GA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Unplug range from its 220V source. Make sure range is not hot from recent usage. You’ll need a #2 Philips driver, preferably one with 14-18 inch length. The old screws will likely be very stubborn about coming loose. Two of them hold bottom element in. Remove the back panel so access to the two connectors on the bottom element are easily removable. Be very careful not to the let the wire connectors from the heating element drop down into the insulation. For the top element, there are four screws holding it in place, I found it was easier to access these two screws leaning the range backward at a slight angle. Take special care again not to let the wires drop down into the insulation. The connectors to the old element will likely need some extra effort to remove. The reconnection to the new elements should be ok. Make sure all screws go back in that were removed. The new elements will be amazing, and baking and broiling will be like new again.
Was this helpful?
Thank you for voting!
When moving the range, the 220 wire popped off the terminal and arced melting the plastic terminal
1 person found this instruction helpful.
  • Randall from ST PETERSBURG, FL
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 2 20 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.
Was this helpful?
Thank you for voting!
The oven just stopped heating. It is probably around 30 years old and has nothing digital to it which I like!
1 person found this instruction helpful.
  • melinda from EL PASO, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then pu rchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!
Was this helpful?
Thank you for voting!
The bottom bake element burned out.
1 person found this instruction helpful.
  • Pauline from DECATUR, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.
Was this helpful?
Thank you for voting!
All Instructions for the JSS014J2
106 - 120 of 416