EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JKP36005 General Electric Range - Instructions

All Instructions for the JKP36005
91 - 105 of 346

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The broiler element had been broken for some time.
0 of 1 people found this instruction helpful.
  • Susan D. from Holland, MA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened w ith the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!
Was this helpful?
Thank you for voting!
Old Bake element burned out. Full of holes
0 of 1 people found this instruction helpful.
  • R.M. from Bethany, OK
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-e yed peas and ham, a New Year's tradition in my neck of the woods.
Was this helpful?
Thank you for voting!
Baking Element In Wall Oven Had Broken
0 of 1 people found this instruction helpful.
  • Charles from Houston, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver
First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete
Was this helpful?
Thank you for voting!
Element was broken
0 of 1 people found this instruction helpful.
  • Aaron from St. Mary's, PA
  • Easy
  • 30 - 60 mins
  • Pliers, Wrench set
Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.
Was this helpful?
Thank you for voting!
Cracked Baking Element
0 of 1 people found this instruction helpful.
  • James from Houston, TX
  • Really Easy
  • 1- 2 hours
First of all let me say, I am grateful you are supplying parts to an oven made in 1984. I noticed the crack the day before Thanksgiving and immediately started looking for the part because Thanksgiving was the least of my worries. I have a countertop broiler to cook the turkey and dressing in but I am catering a huge party in a week and really need the oven in top shape. Due to minor surgery I have not made the repair but I want to say thank you for getting the part to me on Saturday right after Thanksgiving. Wednesday to Saturday with a two day holiday is incredible. Thanks for the great customer service.
Was this helpful?
Thank you for voting!
Original bake element quit working
0 of 1 people found this instruction helpful.
  • Paul from Hartland, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.
Was this helpful?
Thank you for voting!
heating element was on fire and needed to be replaced
1 of 4 people found this instruction helpful.
  • jerome from Farmington Hills, MI
  • Easy
  • 15 - 30 mins
  • Socket set
shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!
Was this helpful?
Thank you for voting!
Old burnt out element
0 of 1 people found this instruction helpful.
  • arthur from annandale, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the two screws holding the mount and then reattached the two wires to the element.
Was this helpful?
Thank you for voting!
Overn would not heat properly.
0 of 1 people found this instruction helpful.
  • David from Calhoun, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!

P.S. Shipping was very fast.
Was this helpful?
Thank you for voting!
Bottom element caught fire and burned out.
0 of 1 people found this instruction helpful.
  • Candice from Houston, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi
Was this helpful?
Thank you for voting!
Bake element failed
0 of 1 people found this instruction helpful.
  • Robert from Des Plaines, AL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the scr ews that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.
Was this helpful?
Thank you for voting!
Bake element cracked and started arcing. (Dramatic!)
0 of 1 people found this instruction helpful.
  • Dave from Portola Valley, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to ve rify that it worked and to burn off any oils on the element.
Was this helpful?
Thank you for voting!
The bake element burned out and broke.
0 of 1 people found this instruction helpful.
  • Helen from Sacramento, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.
Was this helpful?
Thank you for voting!
Old bake element bubbled up, died.
1 of 4 people found this instruction helpful.
  • Edward from Dallas, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!
Was this helpful?
Thank you for voting!
Oven element burned out.
0 of 1 people found this instruction helpful.
  • David from Birmingham, AL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.
Was this helpful?
Thank you for voting!
All Instructions for the JKP36005
91 - 105 of 346