JKP36005 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Top element burned out of oven.
1 of 3 people
found this instruction helpful.
-
Fred from Porter Ranch, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element.
... Read more
Attached the bracket and I turned on the power. I then tested the oven and it worked.
Read less
Was this helpful?
Thank you for voting!
Fireworks! Element blew explosively. Loud noise, major arc. smoke and blew breaker.
0 of 1 people
found this instruction helpful.
-
derek from lynchburg, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
First job was power off! Next step was to remove the two screws holding the element to rear wall of oven. Next is was to gently pull the wires through the hole as far as possible. At this point I needed pliers to stabilize the joint while I removed the two screws of the electrical connection. Now it was easy to clean the oven to remove a
... Read more
rc residue. Now it was a matter of reassemble. Hardest point was getting the screws started in the electrical connections without cross threading while reaching in over the door. Use pliers to ensure you don't bend the connection wires on the element. Finally remount the element with the two original screws. This was the second element to fail. Last time I removed the oven door for better access. I think it was quicker with door on but a lot more bending and reaching.
Read less
Was this helpful?
Thank you for voting!
baking element burned out
0 of 1 people
found this instruction helpful.
-
Michael F. from Bloomfield Hills, MI
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
remove/replace baking element. Relatively simple to do; however, I used the old screws/nuts as they worked better than the new ones which were included.
Was this helpful?
Thank you for voting!
The baking element melted
0 of 1 people
found this instruction helpful.
-
Sarah from Cary, NC
- Easy
- 30 - 60 mins
-
Screw drivers
I researched the part on the internet and found your website. My husband was able to figure out how to install the new element, following the instructions on the site. The most difficult part was reaching into the oven itself.
Was this helpful?
Thank you for voting!
Broil Element
0 of 1 people
found this instruction helpful.
-
Richard from Concord, NH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after re
... Read more
connecting the new element the broiler tested OK. It is once again broiling steak to perfection
Read less
Was this helpful?
Thank you for voting!
Solenoid failed due to excessive heat.
0 of 1 people
found this instruction helpful.
-
Joseph from Martins Creek, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.
Was this helpful?
Thank you for voting!
Lower heating element burned out
0 of 1 people
found this instruction helpful.
-
James from Wayne, OK
- Really Easy
- 15 - 30 mins
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.
Was this helpful?
Thank you for voting!
replace burned out element
1 of 4 people
found this instruction helpful.
-
Dennis from Norcross, GA
- Really Easy
- 15 - 30 mins
-
Socket set
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one
Was this helpful?
Thank you for voting!
Replace Broiler Element
1 of 4 people
found this instruction helpful.
-
William from Chapel Hill, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that ... Read more hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that ... Read more hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Read less
Was this helpful?
Thank you for voting!
bake element was fried
0 of 1 people
found this instruction helpful.
-
jeanne from bodega bay, CA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of ... Read more money on a repairman and a new oven/micro. THANKS.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of ... Read more money on a repairman and a new oven/micro. THANKS.
Read less
Was this helpful?
Thank you for voting!
The Burner Element shorted out on Thanksgiving Day.
0 of 1 people
found this instruction helpful.
-
Richard from Franklin, TN
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed the coverplate screws, slid the element outward, and removed the wire connecting screws. Positioned the new element to reconnect the wires, and discovered this isn't easy to see with trifocals. Succeeded after several failed attempts. Slid the new element into position, and reattached the cover plate.
Was this helpful?
Thank you for voting!
Bake element was showing a burn through spot and broil element was showing signs of wearing out
0 of 1 people
found this instruction helpful.
-
Bruce from Marietta, GA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Cut the power off to the oven. Removed both of the racks in the oven. Removed the 2 screws that hold each element in place. Pulled the bake element out as far as it would go and unscrewed the two wires. Then did the same for the broil element. It has a guard to keep it from dropping down and I had to remove that. The broil element is a li
... Read more
ttle more difficult to remove but i had read that in the previous users writeups. Overall it was a great experience from a price, delivery and installation process.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Replaced burnt out bake element
0 of 1 people
found this instruction helpful.
-
Kathy from Chestnut Hill, MA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Took out the old and put in the new! Easy and inexpensive repair (especially because my husband did it!)
Was this helpful?
Thank you for voting!
Old Broiler Ekement burned out
0 of 1 people
found this instruction helpful.
-
Stacy from Houston, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which wor
... Read more
ked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)
S. Cooke, Houston Texas
S. Cooke, Houston Texas
Read less
Was this helpful?
Thank you for voting!
The lower oven's heating element flamed out on our GE Monogram double oven.
0 of 1 people
found this instruction helpful.
-
Geza from North Potomac, MD
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Wrench set
On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed
... Read more
. Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!
Read less
Was this helpful?
Thank you for voting!