- Home
- JCSP38GV2BB
- Instructions
JCSP38GV2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
heating element shorting out-sparking
1 of 2 people
found this instruction helpful.
-
K from PERRYVILLE, MO
- Really Easy
- 15 - 30 mins
-
Nutdriver
I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven.
... Read more
I then secured the new unit to the oven wall with the two screws.
Read less
Was this helpful?
Thank you for voting!
Just follow the enclosed instructions
1 of 2 people
found this instruction helpful.
-
HAROLD from Tucson, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver
Followed the instructions
Was this helpful?
Thank you for voting!
Baking element burned through.
1 of 2 people
found this instruction helpful.
-
James from Seattle, WA
- Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."
Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.
Re attaching the two-screw panes to hold the element in place finished the project.
Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.
Re attaching the two-screw panes to hold the element in place finished the project.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat bottom
1 of 2 people
found this instruction helpful.
-
Thomas N from Blackfoot, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.
Was this helpful?
Thank you for voting!
only the inner/smaller part of the dual burner is working
2 of 5 people
found this instruction helpful.
-
Albert from South Boston, VA
- Really Easy
- Less than 15 mins
I ordered a new burner assuming As is turns out: nothing wrong with the burner.
Was this helpful?
Thank you for voting!
small (inner) burner was not 'burning'
1 of 2 people
found this instruction helpful.
-
Jerry from Tierra Verde, FL
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
turn off the power at the breaker first
remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)
prop up the stove top on the cardboard box the part came in
pull off the wires one by one and attach to the new burner OR record where each wire goes first
remove the ... Read more old burner (2 screws) and attach the new burner
screw down the stove top
try the burner - when it does not work flip the power breaker back on and then try again
bask in the joy, admiration and wonder directed your way by various family members
remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)
prop up the stove top on the cardboard box the part came in
pull off the wires one by one and attach to the new burner OR record where each wire goes first
remove the ... Read more old burner (2 screws) and attach the new burner
screw down the stove top
try the burner - when it does not work flip the power breaker back on and then try again
bask in the joy, admiration and wonder directed your way by various family members
Read less
Was this helpful?
Thank you for voting!
burned out
1 of 2 people
found this instruction helpful.
-
David from Woodbridge, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.
Was this helpful?
Thank you for voting!
The oven heating element broke in two.
1 of 3 people
found this instruction helpful.
-
Anna from Texas City, TX
- Really Easy
- Less than 15 mins
-
Socket set
Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!
This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices ... Read more !
Thank you,
This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices ... Read more !
Thank you,
Read less
Was this helpful?
Thank you for voting!
Lower bake element shorted out.
1 of 3 people
found this instruction helpful.
-
Val Ray from Idaho Falls, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace o
... Read more
f tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
cooktop inner ring did not work
1 of 3 people
found this instruction helpful.
-
Matthew from Lexington Park, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Dear PartSelect:
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wire ... Read more s to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Matt Brennan
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wire ... Read more s to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Matt Brennan
Read less
Was this helpful?
Thank you for voting!
Bake cycle wouldn't work (broil did)
0 of 1 people
found this instruction helpful.
-
Joe from Levittown, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove dthe two screws and removed the element. Put the new element in and replaced the terminals and screws. Partselected is the fastest shippers on the net.
Was this helpful?
Thank you for voting!
Lower oven element burned out.
0 of 1 people
found this instruction helpful.
-
Gary from Powder Springs, GA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficu
... Read more
lt in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!
Read less
Was this helpful?
Thank you for voting!
The oven element caught on fire and burned in half.
0 of 1 people
found this instruction helpful.
-
Jean from Springdale, AR
- Really Easy
- 15 - 30 mins
-
Nutdriver
Simply turned off the power (circuit box). Unscrewed the screws holding the element in place and detached the element from the wires. Replaced with the new element and replaced the screws. Turned the power back on. Easy as pie and saved lots of $$!
Was this helpful?
Thank you for voting!
the burn element on the bottom burned out
0 of 1 people
found this instruction helpful.
-
DEMETRA from MEMPHIS, TN
- Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
first i unplugged the stove to disconnect all power. next itried using pliers to unscrew the screws and was having a hard time so hubby got the adjustable wrench and it was much easier. after taking out the two screws, i pulled the element out about three inches and disconnected the element from the two wires that hold it in place. then i
... Read more
snapped the new element in place just as the old one was and reattached the element to the stove using the two screws. after assuring that element was secure, i turned my oven on to 300 degrees and voila!!! we're cookin again!!!
Read less
Was this helpful?
Thank you for voting!
Heating element burned out
0 of 1 people
found this instruction helpful.
-
Kim from Munsonville, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the two screws pulled out the old element and slid the new element in and put the screws back in. I used it that night to bake supper
Was this helpful?
Thank you for voting!