- Home
- JCSP38GV2BB
- Instructions
JCSP38GV2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Repair was slow, due to replacement part was incorrect. Original part had two spring loaded spacers, & holes for them to sit in. The replacement part did not have holes. I was able to drill two holes to make it work.
1 person
found this instruction helpful.
-
Victor from FAYETTEVILLE, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 scr
... Read more
ews & turned on circuit breaker.
Read less
Was this helpful?
Thank you for voting!
The center element of the 2-stage electric burner failed.
2 of 4 people
found this instruction helpful.
-
Robert from Cinnaminson, NJ
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was
... Read more
free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.
Read less
Was this helpful?
Thank you for voting!
Small element in center burned into(inoperative
1 person
found this instruction helpful.
-
Douglas from Gravette, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner a
... Read more
ssy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
lynette from Bowling Green, KY
- Easy
- 15 - 30 mins
-
Pliers
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit br
... Read more
eaker back on, turned the oven on.... made brownies (o:
Read less
Was this helpful?
Thank you for voting!
oven coil caught on fire and broke in half!
2 of 4 people
found this instruction helpful.
-
Cynthia from Houston, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorc
... Read more
ed mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL
Read less
Was this helpful?
Thank you for voting!
No heat lower bake unit / Broiler unit heats ok
1 person
found this instruction helpful.
-
Richard L. from Clear Spring, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on
... Read more
terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Read less
Was this helpful?
Thank you for voting!
The old heating erlement basically melted and broke in two places
1 person
found this instruction helpful.
-
Coleen from Danville, IN
- Easy
- 15 - 30 mins
-
Screw drivers
I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!
Was this helpful?
Thank you for voting!
The bake element was burnt out.
1 person
found this instruction helpful.
-
Linda from Fort Collins, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!
Was this helpful?
Thank you for voting!
Heat element burned out
1 person
found this instruction helpful.
-
Donna from Thornville, OH
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..
Was this helpful?
Thank you for voting!
Oven wouldn't heat - wire not exposed
1 person
found this instruction helpful.
-
Donald from Gulf Breeze, FL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip
... Read more
to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.
Read less
Was this helpful?
Thank you for voting!
The phillament ends were pointed straight and the one I removed from the oven were bent in an angle .
1 person
found this instruction helpful.
-
Michael from CLAY, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers
Bent the tips so the phillament can fit inside the oven.
Was this helpful?
Thank you for voting!
Replaced stove top burner element
1 person
found this instruction helpful.
-
Steve from Forest, VA
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical ... Read more to wall outlet. Turn on burner element and verify that it works.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical ... Read more to wall outlet. Turn on burner element and verify that it works.
Read less
Was this helpful?
Thank you for voting!
Small burner of Dual Burner no longer would work.
1 person
found this instruction helpful.
-
Jerry L from Palmetto, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of
... Read more
burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.
Read less
Was this helpful?
Thank you for voting!
element broke
1 person
found this instruction helpful.
-
Richard from NEW BERLIN, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
Was this helpful?
Thank you for voting!
bake element was fried
1 person
found this instruction helpful.
-
William from MARTIN, GA
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
I went by the video
Was this helpful?
Thank you for voting!