EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP79SK2SS General Electric Range - Instructions

All Instructions for the JCBP79SK2SS
91 - 105 of 174

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Small burner of Dual Burner no longer would work.
1 person found this instruction helpful.
  • Jerry L from Palmetto, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.
Was this helpful?
Thank you for voting!
Plastic guide Broken
9 of 25 people found this instruction helpful.
  • NICK from Vernon, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
Burned out
1 person found this instruction helpful.
  • Dean from Elkton, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless
Was this helpful?
Thank you for voting!
burner didn't work
1 person found this instruction helpful.
  • Richard from Coon Rapids, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install
Was this helpful?
Thank you for voting!
The storage drawer came without supports.
2 of 4 people found this instruction helpful.
  • Dock from Aurora, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people found this instruction helpful.
  • Melvin from Portland, TN
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
Burner burned out
1 person found this instruction helpful.
  • Daniel from Norborne, MO
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!
Was this helpful?
Thank you for voting!
Replacing handle spacer
1 person found this instruction helpful.
  • Sherry from SAINT PAUL, MN
  • Easy
  • Less than 15 mins
  • Screw drivers
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this helpful?
Thank you for voting!
inner element not working
1 person found this instruction helpful.
  • Michael from BAY CITY, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person found this instruction helpful.
  • Ron from SAN TAN VLY, AZ
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people found this instruction helpful.
  • Catherine from SEATTLE, WA
  • Very Easy
  • Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap. ... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
Was this helpful?
Thank you for voting!
Original gasket coming apart
1 person found this instruction helpful.
  • Richard from Seminole, OK
  • Really Easy
  • Less than 15 mins
Pulled the old one off (very easy), used popsickle stick to push first end in slot, aligned pins, pushed them in the holes and pushed other end in the slot.
Was this helpful?
Thank you for voting!
Burner no longer heats
1 person found this instruction helpful.
  • Anthony from Apopka, FL
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top insta ll nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!
Was this helpful?
Thank you for voting!
Knob stem broke off.
1 of 2 people found this instruction helpful.
  • DALE from FREMONT, NE
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.
Was this helpful?
Thank you for voting!
only the inner/smaller part of the dual burner is working
2 of 5 people found this instruction helpful.
  • Albert from South Boston, VA
  • Really Easy
  • Less than 15 mins
I ordered a new burner assuming As is turns out: nothing wrong with the burner.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP79SK2SS
91 - 105 of 174