- Home
- JCBP79SK2SS
- Instructions
JCBP79SK2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Oven drawer open and close incorrectly
2 of 2 people
found this instruction helpful.
-
James from Goldsboro, NC
- Easy
- Less than 15 mins
-
Screw drivers
First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens a
... Read more
nd closes smoothly.
Read less
Was this helpful?
Thank you for voting!
Replace Thermostat
2 of 2 people
found this instruction helpful.
-
Russell from Morgantown, WV
- Really Easy
- Less than 15 mins
-
Socket set
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and scr
... Read more
ews. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Read less
Was this helpful?
Thank you for voting!
lens snapped off on the inside-plug was left loose
3 of 6 people
found this instruction helpful.
-
RICKEY from MONTROSE, NY
- Easy
- Less than 15 mins
-
Screw drivers
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this helpful?
Thank you for voting!
Burner spontaneously cycled without knob activation
2 of 3 people
found this instruction helpful.
-
Anil from Milpitas, CA
- Easy
- Less than 15 mins
-
Screw drivers
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Read less
Was this helpful?
Thank you for voting!
Broken rear drawer support
2 of 3 people
found this instruction helpful.
-
Jesse from Knob Noster, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
Was this helpful?
Thank you for voting!
Inside Oven door cracked
2 of 3 people
found this instruction helpful.
-
Deborah from Fort Worth, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
inner coil of burner no good..supposed to last forever!??
2 of 3 people
found this instruction helpful.
-
D. Scott from Melbourne Village, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!
Was this helpful?
Thank you for voting!
Small element in center burned into(inoperative
1 person
found this instruction helpful.
-
Douglas from Gravette, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner a
... Read more
ssy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
Replaced cracked inner oven door glass
1 person
found this instruction helpful.
-
Sherry from SAINT PAUL, MN
- Easy
- 1- 2 hours
-
Screw drivers
This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I
... Read more
had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.
Read less
Was this helpful?
Thank you for voting!
The center element of the 2-stage electric burner failed.
2 of 4 people
found this instruction helpful.
-
Robert from Cinnaminson, NJ
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was
... Read more
free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.
Read less
Was this helpful?
Thank you for voting!
Broke the glass on our oven door due to cold water spilled while it was hot
1 person
found this instruction helpful.
-
Dagmar from WESTMINSTER, CO
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.
Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful whe ... Read more n putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.
For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.
We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.
Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful whe ... Read more n putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.
For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.
We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.
Read less
Was this helpful?
Thank you for voting!
Repair was slow, due to replacement part was incorrect. Original part had two spring loaded spacers, & holes for them to sit in. The replacement part did not have holes. I was able to drill two holes to make it work.
1 person
found this instruction helpful.
-
Victor from FAYETTEVILLE, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 scr
... Read more
ews & turned on circuit breaker.
Read less
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 person
found this instruction helpful.
-
NEIL from ROCKY POINT, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
The light socket cup could no longer hold the bracket that holds the light cover in place.
1 person
found this instruction helpful.
-
Roger from ALPENA, MI
- Really Easy
- 30 - 60 mins
-
Socket set
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with th
... Read more
e part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Read less
Was this helpful?
Thank you for voting!