EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP63SK2SS General Electric Range - Instructions

All Instructions for the JCBP63SK2SS
106 - 120 of 251

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner didn't go on
1 person found this instruction helpful.
  • Mike from Hatfield, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble
Was this helpful?
Thank you for voting!
burner didn't work
1 person found this instruction helpful.
  • Richard from Coon Rapids, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install
Was this helpful?
Thank you for voting!
Bad Line fault displayed on range clock
1 person found this instruction helpful.
  • Vincent J Paola, from GREENWEL SPGS, LA
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Usi ng a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this helpful?
Thank you for voting!
Burner no longer heats
1 person found this instruction helpful.
  • Anthony from Apopka, FL
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top insta ll nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person found this instruction helpful.
  • Ron from SAN TAN VLY, AZ
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
Oven would not heat up
1 person found this instruction helpful.
  • MICHAEL from MORROW, GA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this helpful?
Thank you for voting!
Broiler Unit Failed
1 person found this instruction helpful.
  • William from BOYERTOWN, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.
Was this helpful?
Thank you for voting!
would not heat
1 person found this instruction helpful.
  • Mark from SARASOTA, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Did the repair just like the video shows.
Was this helpful?
Thank you for voting!
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
1 person found this instruction helpful.
  • Melvin from WEBSTER, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this helpful?
Thank you for voting!
The bottome heater element of my oven burned out.
1 person found this instruction helpful.
  • Mary from ALOHA, OR
  • Really Easy
  • 15 - 30 mins
  • Pliers
I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to th e range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!
Was this helpful?
Thank you for voting!
Burned out
1 person found this instruction helpful.
  • Dean from Elkton, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless
Was this helpful?
Thank you for voting!
oven racks old and ugly
1 person found this instruction helpful.
  • Claudene from ORCUTT, CA
  • Very Easy
  • Less than 15 mins
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this helpful?
Thank you for voting!
Oven board went out
1 person found this instruction helpful.
  • Jackie from TICKFAW, LA
  • Very Easy
  • 15 - 30 mins
  • Pliers
One wire at at time then used my razor blade to get front off stuck right back on
Was this helpful?
Thank you for voting!
The lower,BAKE, element had burned in half almost causing a fire.
1 person found this instruction helpful.
  • Joseph from DIAMOND SPGS, CA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the o ven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.
Was this helpful?
Thank you for voting!
Replaced stove top burner element
1 person found this instruction helpful.
  • Steve from Forest, VA
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP63SK2SS
106 - 120 of 251