- Home
- JCBP63SK2SS
- Instructions
JCBP63SK2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The burner would not turn off and I or my wife would have to turn the breaker off.
2 of 2 people
found this instruction helpful.
-
Mark from WOOSTER, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the
... Read more
new switch one by one and screw the new switch to the control panel and replace the back panel and done!
Read less
Was this helpful?
Thank you for voting!
Stove overheated with an F2 error
2 of 2 people
found this instruction helpful.
-
Richard from PHOENIX, AZ
- Easy
- 15 - 30 mins
-
Nutdriver
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this helpful?
Thank you for voting!
Defective switch
2 of 2 people
found this instruction helpful.
-
Mary from EDENTON, NC
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Replaced element control switches
Was this helpful?
Thank you for voting!
broiler unit went out
2 of 2 people
found this instruction helpful.
-
helen from PRINCETON, NC
- Really Easy
- Less than 15 mins
less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.
Was this helpful?
Thank you for voting!
oven racks very old and writing on knobs worn ff
2 of 2 people
found this instruction helpful.
-
Patricia from SAN JOSE, CA
- Very Easy
- Less than 15 mins
Very was ti replace racks and knobs. Very fast mail service
Was this helpful?
Thank you for voting!
Oven temp wouldn't regulate.
2 of 2 people
found this instruction helpful.
-
Ronald from Crumpler, NC
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Followed the directions!
Was this helpful?
Thank you for voting!
Oven could not be turned off once settings were turned on except by unplugging hookup.
2 of 2 people
found this instruction helpful.
-
Charles from BENNETTSVILLE, SC
- Really Easy
- 30 - 60 mins
-
Nutdriver
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this helpful?
Thank you for voting!
Oven would shut down while baking. Stove top would work.
2 of 2 people
found this instruction helpful.
-
Tom from ELIZABETHTON, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certai
... Read more
n areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
Read less
Was this helpful?
Thank you for voting!
Oven would not get come up to temperature
2 of 2 people
found this instruction helpful.
-
Arthur from INDIANAPOLIS, IN
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair ac
... Read more
tions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Read less
Was this helpful?
Thank you for voting!
No Instructions
2 of 2 people
found this instruction helpful.
-
Richard from FAYETTEVILLE, GA
- Difficult
- More than 2 hours
-
Nutdriver, Pliers, Wrench (Adjustable)
Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!
Was this helpful?
Thank you for voting!
Heat element died
2 of 3 people
found this instruction helpful.
-
Andrea Hines from ELGIN, AZ
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Very easy to replace. So easy even a man can do it.
Was this helpful?
Thank you for voting!
Burner spontaneously cycled without knob activation
2 of 3 people
found this instruction helpful.
-
Anil from Milpitas, CA
- Easy
- Less than 15 mins
-
Screw drivers
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Read less
Was this helpful?
Thank you for voting!
lens snapped off on the inside-plug was left loose
3 of 6 people
found this instruction helpful.
-
RICKEY from MONTROSE, NY
- Easy
- Less than 15 mins
-
Screw drivers
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this helpful?
Thank you for voting!
Burner burned out
1 person
found this instruction helpful.
-
Daniel from Norborne, MO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into
... Read more
place replaced two screws that hold cook top down, pluged back into outlet. DONE!
Read less
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people
found this instruction helpful.
-
Melvin from Portland, TN
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!