- Home
- JCBP63SK2SS
- Instructions
JCBP63SK2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Small front burner on our glass top stove died.
3 of 3 people
found this instruction helpful.
-
Robert from FLEMING ISLE, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.
Was this helpful?
Thank you for voting!
OVEN CLOCK CONTROL MALFUNCTIONED
3 of 3 people
found this instruction helpful.
-
Gregoire from N CHESTERFLD, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven
... Read more
worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
Read less
Was this helpful?
Thank you for voting!
none
3 of 3 people
found this instruction helpful.
-
Michael from Laughlin, NV
- Very Easy
- Less than 15 mins
slid the old ones out and slid the new ones in. done
Was this helpful?
Thank you for voting!
Burned out Bake Element
3 of 4 people
found this instruction helpful.
-
Sabina C. from Hershey, PA
- Easy
- 15 - 30 mins
-
Socket set
I ordered part at 10am on Monday and part arrived at Noon on Tuesday 24 hours WHAT MORE can I say... It was all easy and now I have to cook again, so much for the stove is broken excuse.
Was this helpful?
Thank you for voting!
Oven heating element broke
3 of 4 people
found this instruction helpful.
-
ryan from NOVATO, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people
found this instruction helpful.
-
SILVIA from Midlothian, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e
... Read more
stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Read less
Was this helpful?
Thank you for voting!
Oven element broke
3 of 4 people
found this instruction helpful.
-
Rita from LOCUST, NC
- Really Easy
- Less than 15 mins
-
Socket set
Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.
Was this helpful?
Thank you for voting!
Easier than cookig a TV dinner.
3 of 4 people
found this instruction helpful.
-
Robert from olive branch, MS
- Really Easy
- Less than 15 mins
-
Nutdriver
UNPLUG the oven. Following what every else was doing, I removed the element first, then disconnected the contacts. The leads on the contacts are not overly long, so I found myself removing cover on rear of oven when reconnecting red and yellow wires. Required removing two more screws with nut driver. Should I have to replace another elem
... Read more
ent, I would remove rear cover first, unplug wires from element, remove element. Reverse procedure with new element.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.
Read less
Was this helpful?
Thank you for voting!
Replace Thermostat
2 of 2 people
found this instruction helpful.
-
Russell from Morgantown, WV
- Really Easy
- Less than 15 mins
-
Socket set
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and scr
... Read more
ews. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Read less
Was this helpful?
Thank you for voting!
Drawer sticking and not operating smoothly
3 of 5 people
found this instruction helpful.
-
Bill from Philadelphia, PA
- Easy
- Less than 15 mins
-
Screw drivers
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
Was this helpful?
Thank you for voting!
Broken drawer glider
2 of 2 people
found this instruction helpful.
-
James from RANCHO MIRAGE, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this helpful?
Thank you for voting!
Drawer support broke
2 of 2 people
found this instruction helpful.
-
Charles from BOULDER, WY
- Really Easy
- Less than 15 mins
-
Nutdriver
Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plas
... Read more
tic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.
Read less
Was this helpful?
Thank you for voting!
Just didn't work no pwr to it
2 of 2 people
found this instruction helpful.
-
Jerry from HOPEWELL, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this helpful?
Thank you for voting!
front lift burner not working and surface light on with everything off
2 of 2 people
found this instruction helpful.
-
kevin from GAYLORD, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this helpful?
Thank you for voting!
Top glass top burner wasn’t working
2 of 2 people
found this instruction helpful.
-
Robert from PAWTUCKET, RI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I first ordered the wrong part and had to call customer service. They handled the return and ordered the new piece beautifully!! The installation was really simple. Once I took out two screws holding the top down, I removed three clips holding the burner on then switched out the electrical leads. Put everything back and it worked perfect
... Read more
ly!!
Read less
Was this helpful?
Thank you for voting!