EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP36DM1WW General Electric Range - Instructions

All Instructions for the JCBP36DM1WW
91 - 105 of 241

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
front lift burner not working and surface light on with everything off
2 of 2 people found this instruction helpful.
  • kevin from GAYLORD, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this helpful?
Thank you for voting!
just needed new GE burner bowls
2 of 2 people found this instruction helpful.
  • Jacqueline from E WENATCHEE, WA
  • Very Easy
  • Less than 15 mins
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
Was this helpful?
Thank you for voting!
Broken drawer glider
2 of 2 people found this instruction helpful.
  • James from RANCHO MIRAGE, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this helpful?
Thank you for voting!
broiler unit went out
2 of 2 people found this instruction helpful.
  • helen from PRINCETON, NC
  • Really Easy
  • Less than 15 mins
less then ten minutes, used a electric screw driver and in a snap, finished, I always buy my parts on line at parts select my stove is old but in good condition except parts give out sometimes and I just order part and keep on cooking.
Was this helpful?
Thank you for voting!
Burner spontaneously cycled without knob activation
2 of 3 people found this instruction helpful.
  • Anil from Milpitas, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Was this helpful?
Thank you for voting!
lens snapped off on the inside-plug was left loose
3 of 6 people found this instruction helpful.
  • RICKEY from MONTROSE, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this helpful?
Thank you for voting!
My burner trays were worn out and I needed new ones
1 person found this instruction helpful.
  • Mary Jane from La Junta, CO
  • Really Easy
  • Less than 15 mins
I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people found this instruction helpful.
  • Melvin from Portland, TN
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
Bad Line fault displayed on range clock
1 person found this instruction helpful.
  • Vincent J Paola, from GREENWEL SPGS, LA
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Usi ng a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person found this instruction helpful.
  • Ron from SAN TAN VLY, AZ
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
Old burner bowl needed to be replaced
2 of 4 people found this instruction helpful.
  • bonnie from N KINGSTOWN, RI
  • Very Easy
  • Less than 15 mins
Took out the old & put in the new one-Done!
Was this helpful?
Thank you for voting!
Oven would not heat up
1 person found this instruction helpful.
  • MICHAEL from MORROW, GA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this helpful?
Thank you for voting!
Oven board went out
1 person found this instruction helpful.
  • Jackie from TICKFAW, LA
  • Very Easy
  • 15 - 30 mins
  • Pliers
One wire at at time then used my razor blade to get front off stuck right back on
Was this helpful?
Thank you for voting!
Broiler Unit Failed
1 person found this instruction helpful.
  • William from BOYERTOWN, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.
Was this helpful?
Thank you for voting!
The bottome heater element of my oven burned out.
1 person found this instruction helpful.
  • Mary from ALOHA, OR
  • Really Easy
  • 15 - 30 mins
  • Pliers
I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to th e range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!
Was this helpful?
Thank you for voting!
All Instructions for the JCBP36DM1WW
91 - 105 of 241