- Home
- JCBP36DM1WW
- Instructions
JCBP36DM1WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burned out broiler element
5 of 6 people
found this instruction helpful.
-
Amanda from Thornton, CO
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
Don't forget to unplug and/or turn off the main breaker!
Was this helpful?
Thank you for voting!
change broiler element
5 of 6 people
found this instruction helpful.
-
lee from bethel, CT
- Really Easy
- Less than 15 mins
-
Nutdriver
removed 2 1/4in. drill screws holding broiler element to oven removed 2 1/4in.drill screws holding broiler element to top of oven removed female spade connectors ffom old element and reversed assembley very easy
Was this helpful?
Thank you for voting!
GE oven showed "F2" error code and was over-heating
5 of 6 people
found this instruction helpful.
-
Kyle from AURORA, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver
I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from
... Read more
the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.
Read less
Was this helpful?
Thank you for voting!
surface burner switch was burned
5 of 6 people
found this instruction helpful.
-
abbas from redmond, WA
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove t
... Read more
he swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Read less
Was this helpful?
Thank you for voting!
Oven Wouldn't Heat
7 of 13 people
found this instruction helpful.
-
Russell from Yuma, AZ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Replaced
Was this helpful?
Thank you for voting!
Broiler element was sparking
4 of 4 people
found this instruction helpful.
-
jeff from NEENAH, WI
- Very Easy
- Less than 15 mins
-
Nutdriver
I removed oven door so i could reach easier. Then removed screws from Broiler element at the back of the oven. Pulled off connected wires. Slid wire connectors on new element and screwed bracket in.
Was this helpful?
Thank you for voting!
temp sensor in oven was failing.
4 of 4 people
found this instruction helpful.
-
Chad from FRANKLIN, NC
- Easy
- 15 - 30 mins
-
Nutdriver
I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However,
... Read more
after the new sensor the oven will maintain a more even temperature for the cycle.
Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.
At best a temporary fix for a an appliance this old.
Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.
At best a temporary fix for a an appliance this old.
Read less
Was this helpful?
Thank you for voting!
Oven Temp. went too high and the door locked. Burnt the food
4 of 4 people
found this instruction helpful.
-
Nathan from BILLINGS, MT
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws
... Read more
off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.
Read less
Was this helpful?
Thank you for voting!
F2 Error on Display
4 of 4 people
found this instruction helpful.
-
Tom from FORNEY, TX
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Read less
Was this helpful?
Thank you for voting!
F2 fault code kept appearing on oven
5 of 7 people
found this instruction helpful.
-
emmett from rocky mount, NC
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Thea
... Read more
ded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.
Read less
Was this helpful?
Thank you for voting!
nylon guide was broke off
5 of 7 people
found this instruction helpful.
-
Lathan from Goodyear, AZ
- Really Easy
- 15 - 30 mins
-
Screw drivers
took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.
Was this helpful?
Thank you for voting!
every thing went great
5 of 8 people
found this instruction helpful.
-
CLYDE from SAINT PETERSBURG, FL
- Really Easy
- Less than 15 mins
-
Socket set
every thing went great
Was this helpful?
Thank you for voting!
The bake element quit working.
5 of 8 people
found this instruction helpful.
-
Wiley from Port Orchard, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.
Was this helpful?
Thank you for voting!
oven would not heat
5 of 8 people
found this instruction helpful.
-
Jim from Williamsburg, VA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried t
... Read more
he oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.
Read less
Was this helpful?
Thank you for voting!
When I took out the baking element, the wires went up inside because they were so short, I got a hold of one of them but couldn't get a hold of the other.
4 of 6 people
found this instruction helpful.
-
Daniel from SPRINGFIELD, OR
- Very Difficult
- More than 2 hours
-
Screw drivers, Socket set
Had to pull out the refrigerator and put it in the dining room in order to pull out the stove to be able to get to the back of it. Had to take off the back of the stove to get to the wiring for the baking element, so at that point I replaced the broil element at the same time. Not a easy job at all.
Other Parts Used:
Was this helpful?
Thank you for voting!