- Home
- JCBP36DM1WW
- Instructions
JCBP36DM1WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The oven did not get up to or hold the correct temperature
6 of 6 people
found this instruction helpful.
-
Robert from ARROYO GRANDE, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the c
... Read more
onnector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.
Read less
Was this helpful?
Thank you for voting!
Oven temperature would not go above 240 degrees
7 of 9 people
found this instruction helpful.
-
Glenn from Grapevine, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven tem
... Read more
perature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.
Read less
Was this helpful?
Thank you for voting!
F2 error; over heating, unknown reason
6 of 6 people
found this instruction helpful.
-
Tim from LEAVENWORTH, WA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I just followed the instructions on the link provided with the part
Was this helpful?
Thank you for voting!
The oven was not getting very hot because the bake element had stopped working (broiler element was fine).
6 of 7 people
found this instruction helpful.
-
Linda from Bella Vista, AR
- Really Easy
- Less than 15 mins
-
Pliers
I turned off the breaker to the stove, took the oven racks out, used my pliers to remove the nuts that hold the bake element in place, then used the pliers to disconnect the old element from the wires in the back of the stove. Connected the new element, screwed the nuts back in, flipped the breaker back on, and turned on the oven. Ten min
... Read more
utes, tops.
Read less
Was this helpful?
Thank you for voting!
switch went to high setting no matter what the setting was
10 of 19 people
found this instruction helpful.
-
Frank from Glen Cove, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this helpful?
Thank you for voting!
the bake element broke
5 of 5 people
found this instruction helpful.
-
Daniel from Apex, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I removed the 2 screws and removed the bake element, replaced the new one
Was this helpful?
Thank you for voting!
Red Light On
5 of 5 people
found this instruction helpful.
-
Lawrence from DECATUR, AL
- Really Easy
- 30 - 60 mins
Red Light Off
Was this helpful?
Thank you for voting!
Broiler not working
6 of 8 people
found this instruction helpful.
-
Teresa M from denver, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turned off electricity. Removed two screws that held the element in back of oven. Removed the two screws that held it up to top of oven. Disconnected the two wires that held it in the rear of the oven. Removed it from the top support. Replaced the old element with the new in the support. plugged it it, replaced all four screws. Turn
... Read more
ed on the electricity and turned on the oven-it worked!
Read less
Was this helpful?
Thank you for voting!
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
6 of 8 people
found this instruction helpful.
-
Brian from DOVER, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to
... Read more
access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.
Read less
Was this helpful?
Thank you for voting!
Oven in accurate temp too low.
6 of 8 people
found this instruction helpful.
-
Joseph from LIBERTY HILL, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.
Was this helpful?
Thank you for voting!
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
6 of 8 people
found this instruction helpful.
-
Mary from Bolton, MA
- Really Easy
- Less than 15 mins
-
Socket set
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
Was this helpful?
Thank you for voting!
The drawer support broke.
8 of 14 people
found this instruction helpful.
-
Cindy from Golden Valley, ND
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the screw from the broken piece and put the new piece on and put the screw on.
Was this helpful?
Thank you for voting!
Broke oven door handle while unloadin new stove.
6 of 8 people
found this instruction helpful.
-
Tom from Mt. Pleasant, MI
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Wrench set
loosen interior panel of oven with star driver. Removed broken arm. install inner screw and then install final screw to both panels and handle.
The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.
Other than that it when sm ... Read more oothly.
The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.
Other than that it when sm ... Read more oothly.
Read less
Was this helpful?
Thank you for voting!
The element split open and burned out
5 of 6 people
found this instruction helpful.
-
Thomas from Houston, TX
- Easy
- Less than 15 mins
-
Socket set
I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,
Was this helpful?
Thank you for voting!
I broke the left drawer glide on our oven
5 of 6 people
found this instruction helpful.
-
Keith from Freeport, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I unscrewed to old glide and replaced it then re attached the screw
Was this helpful?
Thank you for voting!